User manual DATAVIDEO HS-550

[. . . ] Hand Carry Studio (ITC-50+DAC-200+TLM-702+SE-500) HS-550 Table of Contents Warnings and Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Standard Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Two Year Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] In a wipe transition, the change from one source to another happens along a predefined edge. It is like one source image is being pulled back or pushed on top of another source image. Depending on the button selected the starting point and direction of the wipe is changed. But a picture is worth a thousand words, so. . . Select a main source and sub source, select a Wipe, or Fade from the buttons above, press the "Preview" button and see what it would like. Then, perform the actual transition manually by moving the T-bar up and down. See the next page for a list of wipe transitions and variations. 12 List of Wipe transitions and parameters (suitable for photocopying) Any Wipe works in conjunction with the Border control. A represents the current source and B represents the sub source that will replace A during the transition. Vertical wipe, from middle out to left and right sides at the same time. Vertical wipe, from left to right side. Horizontal wipe, from top to bottom of screen. Right angle wipe, from upper left corner to lower right corner. Right angle wipe, from upper right corner to lower left corner. Block wipe, from center to full screen. Horizontal wipe, from middle out to top and bottom at the same time. Vertical wipe, from right to left side. Horizontal wipe, from bottom to top of screen. Right angle wipe, from lower left corner to upper right corner. Right angle wipe, from lower right corner to upper left corner. Dissolve or Fade from Main source to Sub source 13 Effects There are two places on the HS-550 where you can add effects: in the Transition Effects section (15. ) and in the Video Effects section (5-8. ). Some of these work on a single source, and some need two or four sources to work. Select a Main Video source and try the following: In the Transition Effects section, select the WIPE effect you wish to use. You could also add a border to the edge by turning on the BORDER effect (10. ). In the Video Effects section, try the Quad effect (5. ). Press the button to engage the effect; the LED will light. You can see all 4 input sources showing on the program monitor at the same time. No other cuts or transitions can be performed until the Quad effect is toggled off. For Split effect (6. ), select a sub source for right hand side window. Then, press the "SPLIT" button. You will see Main source on left hand side, and Sub source on right hand side. Simple cuts can be performed along the main and sub source rows. Transitions are not possible until the Split effect is toggled off. PIP effect (7. ), which stands for Picture in Picture. As you might guess, this effect requires a Main and Sub Video Source. Assuming you have valid inputs on Channel 1 and 2, select Channel 1 as the Main Source and Channel 2 as the Sub Source. [. . . ] The tally indicator lights will continue to work even when the Power LED is not on, and the channel is not active. 27 Cable Assignments Headset, Jack plug and 5pin XLR Please Note: If you only want to extend the reach of the ITC-100SL Belt Pack cabling then Datavideo already sell pre-manufactured XLR cabling for doing this in 20m (CB-3) and 50m (CB-4) lengths. Please ask your local dealer for price and availability of additional CB-3 and CB-4 cables. ITC-100 XLR cable / 5pin XLR Connector on ITC-100SL Pin 1 2 3 4 5 Cable Red Black Shield Green White Tally Red Assignment Tip (Talk & Call) Common with Ground of XLR +12v DC power to ITC100SL Tally Yellow 5pin XLR Cable is a straight through cable pin 1 to pin 1, pin 2 to pin 2 etc ITC-100SL Belt pack 3. 5mm Jack socket Headset connector Please Note: For connecting a professional headset Datavideo can supply a mini jack to XLR adaptor cable which would support headsets with a Dynamic microphone. Please contact your dealer or local Datavideo office for more information on this XLR to Jack plug adaptor cable. In the case of a professional headset with an Electret microphone a small SDM of 1yf/1uf (for decoupling ac) will be required on the Jack Tip/XLR pin 2 cabling. Jack Tip Headset XLR Pin 2 Assignment Microphone (can be Dynamic or Electret) Ring Pin 4 Earphone (Impedance range 8-100) (ideally 30-40) Ground/Sleeve Pins 1 & 3 Common Ground 28 TLM-702 Functions - Front Panel 1. Each monitor has a two color tally light indicator which can be connected to the Datavideo RMC 140, SE500 or similar products. [. . . ]