User manual DAXTEN IBOOT

[. . . ] iBoot Web Enabled Remote Power Control Table of Contents iBoot Setup Important Safety Information General Description Hardware Installation Ethernet Connections A/C Power Connections 13 2 3 5 Device Settings TCP/IP Settings Auto-Ping Heartbeat Passwords Forgotten Password iBoot Configuration Setting IP Address Using DHCP Using Web Browser Access Using ibootrst. exe Using ARP / Ping 8 Advanced Operation Auto Ping Heartbeat Monitor Control Programs Direct TCP Control 16 Web Browser Operation Password Protection Control & Status Page 11 Specifications User Settings Tech Support & Warranty More Power Control Solutions 22 22 23 24 Ver: 2. 0 and up 11 Park Place / Paramus, NJ 07652 201-967-9300 www. dataprobe. com Ver 2. 0 and up iBoot Page 2 IMPORTANT SAFETY INSTRUCTIONS When using this product, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Follow all warnings and marked on the product. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. [. . . ] To access the Setup page, the Setup Password must be used for the initial login. The factory default for the Setup Password, as well as the operation password is PASS. When you are finished iBoot, click on Logout. If you close browser window without clicking Logout, there will minute delay before you access iBoot. with your first be a two can re- iBoot uses an inactivity timer for security. When there is no activity for 2 minutes, the user is logged out and the password will need to be entered again for access. This is to prevent accidental lockout by leaving the user logged in. Ver 2. 0 and up iBoot Page 13 iBoot Setup iBoot setup section consists of several pages. Access any page via the buttons on the left of the page. Each time a setting is changed click on the Apply button for that page to save the changes in iBoot. Device Settings Device Name: Set a 20 name to be displayed on the Home page. This assists in identifying which iBoot is accessed. This is the time the power will be off reboot, or on during a power Character top of the being seconds length of during a burst. TCP/IP Settings IP address: Enter either a address, or address 0. 0. 0. 0 to Automatic IP addressing via Once you click Apply for this also click the Reboot button appear at the top of the page. IP address will not take effect unit is rebooted. section, that will The new until the Upon Clicking Reboot, a page indicates the new the device. Use this new URL to access iBoot. URL for Subnet Mask: Change if required. Consult your network manager for more details. This will be automatically set if using DHCP Gateway: Change if required. Consult your network manager for more details. This will be automatically set if using DHCP HTTP Port: This setting is used to allow access to iBoot on a port other than the Web standard Port 80. If the port is changed, you will need to identify the port Ver 2. 0 and up iBoot Page 14 number when you enter iBoot's IP address into your browser: if the new port is 9100 then use address http://192. 168. 1. 254:9100 to access iBoot. After changing the port, a reboot is necessary. Consult your Network Administrator for available port assignments. Click on the Reboot button at the top of the page to install the new port. Auto-Ping Setup See Advanced Operation for Auto-Ping Setup Heartbeat Setup See Advanced Operation for Heartbeat Setup Power and System Passwords Two passwords are provided. [. . . ] Dual Jack Hub Built-in IP Addressed Internal HTTP Web Server, Forms Processing Browser required User Settings Location MAC Address IP Address Subnet Mask Gateway HTTP Port Auto-Ping Address Auto-Ping Port Heartbeat Port Notes: Record your Setup here for reference Ver 2. 0 and up iBoot Page 23 TECHNICAL SUPPORT, RETURNS and WARRANTY Dataprobe Technical Support is available 8:30AM to 5:30PM ET to assist you in the installation and operation of this product. To obtain Technical Support call our Tech Support Hotline at 201967-8788, or Email us at tech@dataprobe. com. Please have the following information available when you call: · · · · Model of Product Serial, Lot and/or Version Numbers Data of Purchase Name of Seller (if other than Dataprobe) If you purchased this product through an Authorized Dataprobe Reseller, you should contact them first, as they may have information about the application that can more quickly answer your questions. WARRANTY Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for a period of One Year from the date of initial purchase. If the product should prove defective within that period, Seller will repair or replace the product, at its sole discretion. [. . . ]