User manual DCS BGB131

[. . . ] THE PROFESSIONAL SIDE BURNER Use and Care Guide MODELS: BGB131 BGB132 BGB131-BI BGB132-BI A MESSAGE TO OUR CUSTOMERS We are glad that you selected the Professional Side Burner by DCS. Because this appliance contains features not found on any other burner, we recommend that you read this entire booklet before your first use. Keep it in a handy place as it has answers to questions that may occur during future use. Feel free to contact us if we can help you. [. . . ] For LP units, check with a full cylinder. Make sure all control valves are in the "OFF" position. Turn the gas supply "ON" Check all connections from the supply line . 03) up to the manifold pipe assembly (Fig. Apply the soap solution around the connection with a spray bottle, brush, or rag. Soap bubbles will appear where leak is present. If a leak is present, turn off gas supply, tighten any leaking fittings, turn gas on, and recheck. FIG. 05 WARNING: IMPORTANT! Inspect the gas supply piping or hose prior to turning the gas "ON" If there is . evidence of cuts, wear or abrasion, it must be replaced prior to use. Do not use the Professional Side Burner if the odor of gas is present. Turn the control knob to "OFF" then turn off the gas supply. If using LP, is there gas in the , tank?Always keep your face and body as far away from the burner as possible when lighting. LIGHTING INSTRUCTIONS First remove the burner cover and any cooking utensils from the burner grate. Push and hold the ignition button, turn the control knob to the "HI" position until the burner is lit or 4 seconds pass. If the burner doesn't ignite, wait 5 minutes for any accumulated gas to dissipate then try again. If the burner will not light after several attempts, check the troubleshooting instructions on page 14. To light burner manually see page 11, "Match Lighting" . Control Knob Ignition FIG. 06 BGB132 Shown 10 LIGHTING INSTRUCTIONS MATCH LIGHTING Hold a fireplace lit match near the burner ports, turn the control knob counterclockwise to "HI" Move . your hand immediately once the burner is lit. Rotate the control knob to the desired setting. Note: If you are using propane gas, a slight pop or flash may occur at the burner ports a few seconds after the burner has been turned "off". This "extinction pop" is normal for propane gas. Cap BURNERS Your new side burner is equipped with burners typical of those used in restaurants (Fig. These burners are designed for maximum cleanability and controlability. The burner should never be operated if the cap is not in place. FIG. 07 BURNER EFFICIENCY AND FLAME CHARACTERISTICS It is necessary to keep the burner ports and the igniters clean for proper lighting and efficient performance of the burners. [. . . ] STL (BGB131 MODEL) DRIP PAN HANDLE DBI (BGA131-BI MODEL) DRIP PAN HANDLE 131/132 (BGB131 MODEL) 1. 5VDC BATTERY AA PART NO. 33316 18204-01 18403 12020 12272 12333 12332 12321 33314 33434 33315 12200-17 12200-08 32348-02 33306-02 33035 33307 16567 ITEM 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 DESCRIPTION BEZEL CONTROL KNOB IGNITION MODULE WIRE BLACK W/ TERMINALS 8" WIRE BLACK W/ TERMINALS 10" TUBING 5/16" (9"LENGTH) ELBOW 1/8NPT X 5/16 T. O. D. FERRULE 5/16 NUT M22 JET HOLDER NUT 1/2-24UNF MANIFOLD (BGB131-BI MODEL) MANIFOLD (BGB131 MODEL) MANUAL GAS VALVE VALVE PANEL (BGA131-BI MODEL) VALVE PANEL (BGB131 MODEL) VALVE PANEL SCREWS (BGB131-B1) ELECTRODE SPRING ELECTRODE CLIP ELECTRODE PART NO. 14006-PL 14351 16566 16438-03 16438-06 18537 18530 18301-02 12150 18301-01 18230-02 18502 13017-01 33351-PA 33320-PA 15002-41 12224 12230 12231 15 DOUBLE SIDE BURNER PARTS LIST FOR BGB132 & BGB132-BI 4 5 6 1 3 25 24 2 26 21 10 23 20 27 22 19 28 29 16 17 18 12 11 7 8 9 30 31 32 15 14 13 NOTE: Part list typical for BGB132 & BGB132-BI models. [. . . ]