User manual DCS DCS-DRH-48N INSTALLATION INSTRUCTION

[. . . ] PROFESSIONAL DEL REY HEATER Use and Care Guide and Installation Instructions MODELS: DCS-DRH48N A MESSAGE TO OUR CUSTOMERS Thank you for selecting DCS Professional Del Rey Heater. Because of this appliance's unique features we have developed this Use and Installation Guide. It contains valuable information on how to properly operate and maintain your new appliance for years of safe and enjoyable use. To help serve you better, please fill out and submit your Ownership Registration Card by visiting our website at www. dcsappliances. com and selecting "Customer Service" on the home page and then select "Ownership Registration" or submit the enclosed Ownership Registration Card to the address below. [. . . ] Electrical supply line shortage and / or control overheating may occur. The heater must be installed in a location such that it is accessible for servicing and have no restriction of air flow to the air inlet of the heaters casing. MOUNTING Each heater must be installed such that the minimum clearance to combustibles are maintained. Combustible materials are defined as wood, paper, foliage, plastic, plexiglass or other materials capable of being ignited and burned. Such materials shall be considered combustible even though flameproofed, fire retardant treated or plastered. Additional clearances may be required for glass, painted surfaces and other materials which may be damaged by radiant or convection heat. ELECTRICAL A 24 VAC, 40 VA transformer has been included with the product. The on-off control of the heater should be controlled from 120 VAC side of the transformer. A UL approved outdoor wall switch must be used for this purpose. The transformer must be mounted a minimum of 12" from the heater in a weather protected cover. Do not use heater until all connections have been leak tested and do not leak. When leak testing, refer to the connections diagrams. Only those parts recommended by the manufacturer should be used. Substitution can void warranty. LEAK TEST: Make a soap solution of one part liquid detergent, and one part water. The soap solution can be applied with a spray bottle, brush or rag, soap bubbles will appear where a leak is present. "OFF" "ON" POSITION FACTORY DEFAULT Turn the gas supply "ON" check for leaks at leak points. If a leak is present, turn off supply, tighten any leaking fittings, turn gas on and recheck. Note: There is a manual shut-off lever on the internal heater control valve/regulator. This lever is shipped in the "ON" position (Default position). 11 LIGHTING/OPERATION INSTRUCTIONS LIGHTING INSTRUCTIONS Upon installation of the heater and completion of the gas line and electrical supply to each heater, follow the steps below for Lighting Instructions. Lighting instructions are also provided on the control panel of the heater. Turn gas and power to "ON" The igniter should light within the first 4 seconds. sensor will shut off the hot surface igniter. The igniter will attempt to light 3 times before "locking out" . During initial installation, this will happen if the gas line is not purged. To reset the control, shut off the power to the unit and wait 5 seconds. Turn power back to "ON" position. [. . . ] Be sure valve switch is on (in the up position). The transformer must be mounted outside of unit to protect it from the heat and ensure long service life. Refer to page 10. Do not install transformer inside unit. 16 HEATER PARTS LIST ITEM 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) DESCRIPTION Wall Plate R/H Mounting Channel Body Plate R/H Screws Back Panel Wall Plate L/H Mounting Channel Body Plate L/H Collector Box Mini Ingiter Control Valve Ignition Module Cover Remote Sensor Bracket PART NO. 22019 22014 22012 15001-26 22002 22019 22014 22012 22016 16325 18270 22022 22015 ITEM 14) 15) 16) 17) 18) 19) 20) 21) 22) 23) 24) 25) 26) 27) DESCRIPTION Remote Sensor Ignition Module Wiring Harness Service Panel Frame Windscreen Bottom Frame Windscreen Top Egg Crate I/R Burner Transformer Nipple Blk 1/2 NPT x 3-1/4 Reducer 1/2 x 3/8 NPT Orifice Fitting Orifice Spud Type #29 Flue Spacer PART NO. 13055-5 18271 18272 22006 22007-02 22007-01 22010 18227 16381 18018-21 18130 13024 13025-29 22003 1 4 2 27 3 5 9 10 4 7 19 26 21 25 18 13 20 17 16 14 15 23 12 24 8 11 6 22 17 Ground Valve 2 1 3 120 VAC 60 Hz 24 VAC 4 6 2 MINI IGNITER 18 ELECTRODE SENSOR 7 1 WIRING DIAGRAM NOTE: 1. [. . . ]