User manual DE DIETRICH DPE7729XF

[. . . ] Short title or reference to the measurement and calculation methods used to establish compliance with the above requirements. The performance of each individual burner is calculated according to standard EN 30-2-1 + A1:2003 + A2:2005 The total efficiency of the hob is calculated according to the EU Regulation 66/2014 Par. 2 The efficiency is calculated only for the burners with a nominal capacity exceeding 1, 16 KW ( EN 30-2-1 + A1:2003 + A2:2005; Par. 1) Information which is relevant to the customer to minimize the energy consumption during usage: Energy Saving Tips: use pots having flat base, Use pots with proper size, use pots with lid, minimize the amount of liquid or fat, when liquid starts boiling reduce the setting. [. . . ] It is advisable to isolate the appliance from the piece of furniture below with a separator, leaving a depression space of at least 10 mm (1. If the hob is going to be installed on the top of an oven, precautions must be taken to guarantee an installation in accordance with current accident prevention standards. Under no circumstances keep any sprays or pressurised containers in any compartment below the hob (see "Safety guidelines“ chapter). €¢ Remove the "pan supports", burner caps and burner heads, noting their original positions. €¢ Turn the hob upside down and place 7 •1 INSTALLATION 1•3 - GAS CONNECTION: If the hob is to be installed above an oven or if other nearby heating appliances could heat and damage the gas hose, then it is essential that a rigid pipe is installed instead. If a flexible hose is used (as is the case of butane gas) then it must not be installed in a place where it may be in contact with a moving part of the kitchen unit or a location likely to get cluttered. No flexible hoses with a limited service life may be longer than 2 metres and must be accessible for inspection along their entire length. They must be replaced before their expiry date (printed on the hose). Whatever means of connection is chosen, make sure that it is gastight when installed, using soapy-water. In France, you must use a hose or pipe stamped NF Gaz . The gas connection must comply with the regulations in force in the country where it is installed. The plug must be accessible after the hob is installed. Cross section of the cable to be used 220-240 V˜ - 50 HZ gas Cable H05RR-F - T90 Cross section of conductors in mm² Two conductors, One of which is an earth 0, 75 The protective conductor (green/ yellow) is connected to the earth terminal on the hob and must also be connected to the installation's earth terminal (1. If the supply cable is damaged, it must be replaced by a cable or special set available from the manufacturer or its after-sales department. So that you can find the references for your appliance without difficulty in the future, we recommend that you make a note of them on page (6. 1) "After-sales service and customer relations“ (that page also tells you where to find them on your appliance). 8 •1 INSTALLATION In an existing installation, a flexible hose fitted C with jubilee clips (in conformity with the local regulations). In this case an end connector must be used with a sealing washer A fitted between the end connector B and the elbow on the hob. Yo u c a n p u r c h a s e t h e e n d connector and the sealing washer from your after-sales department. Tighten the end connector to a torque not exceeding 25 N. 1•4 - CHANGING THE TYPE OF GAS: Your appliance is supplied ready for use with natural gas. The injectors required for adapting it to butane/propane can be found in the plastic bag containing this guide. [. . . ] €¢ Reminder: Remember that gas hobs are delivered set up for use with mains gas (natural gas). €¢ Check that the retarder screws are properly adjusted (see "Changing gas type" paragraph). €¢ Check that the burners and injectors underneath them, burner assemblies, are clean, etc. €¢ Use smaller pans on the burners close to the knobs. [. . . ]