User manual DEI OHV1021 OWNERS GUIDE

[. . . ] OWNER'S GUIDE INSTALLATION GUIDE 10. 2" (16:9) Overhead Video Monitor MODEL OHV1021 © 2005 Directed Electronics, Inc. N81121 03-05 NON-TRANSFERABLE LIMITED ONE YEAR CONSUMER WARRANTY Directed Electronics, Inc. (Directed) promises to the original purchaser that the new automotive video monitor and/or source unit(s) (the Product) that is purchased and installed from a Directed authorized dealer more than ninety (90) days after the purchase of a new vehicle are warranted for a period of one (1) year from date of purchase of the Product. Directed promises to the original purchaser that all video accessories will be free from defects in materials and workmanship under normal use and condition for a period of ninety (90) days after the date of purchase. [. . . ] RIGHT (Cursor) (wide, zoom, full, normal) 37. AUTO (auto programming of TV channels)* 48. PROGRAM IR REMOTE FEEDTHROUGH The remote will operate, through the monitor, and transmit commands to other compatible devices attached to the AV1 or AV2 source at the switch-box. The IR signals are compatible with models DV2602, DV2605 DVD players, and TV100 tuner. NOTE: This remote is for the operation of the LCD screen and for the optional DVD player. Some remote buttons only function when the optional DVD player is installed in the monitor. * These buttons are for use only with the TV tuner (model TV100). © 2005 Directed Electronics, Inc. 11 BATTERY REPLACEMENT NOTE: Before using remote after installation, remove the battery plastic protective slip. Remote Controller + side Battery Latch Battery Holder 1. Move the small latch to the right and slide out the battery holder. Remove old battery and replace it with a new battery (CR2025) with the positive "+" sign facing as shown above. Push battery holder back into its compartment until it is locked. PRECAUTIONS 1. Do not misuse battery by shorting the positive "+" and negative "-" terminal or put it into fire. Overheating may cause the battery to explode and cause a fire hazard. If the remote is not to be used for a long period, remove the battery from the remote to prevent damage from battery leakage. To avoid accidents, prevent children from playing with the battery. 12 © 2005 Directed Electronics, Inc. Operating the Monitor OPEN/CLOSE THE DISPLAY MONITOR To open the display monitor, push the "OPEN" button and pull the monitor down by the middle of the LCD to the desired position. WARNING: THE LCD MONITOR MUST ALWAYS BE OPENED, CLOSED, OR POSITIONED FROM THE MIDDLE OF THE SCREEN AS SHOWN BY THE POINTING HAND BELOW. DO NOT USE THE CORNERS OF THE SCREEN, THIS CAN RESULT IN DAMAGE/LEAKAGE OF THE SCREEN. To Open--push center button Use this portion of the screen for opening, closing, and positioning. Open Pos ition To close the display monitor, push the LCD screen up until it latches closed with an audible click. Note: The ignition key must be in the Accessory or Ignition position in order for the monitor to have power. © 2005 Directed Electronics, Inc. 13 Power Up/Down the Display Monitor The unit will power up when the display monitor is unlatched and pulled down. (If the unit does not power up, press the Power side of the LCD screen. To turn the power off to the unit, press and hold for 3-seconds the POWER the display monitor is placed in the closed and latched position. If the hand icon or "INVALID KEY" displays in the upper left-hand corner of the screen when button on the button on either the remote or the Power button on the left remote or the Power button on the left side of the LCD screen. The power will also shut Off when using the remote, it indicates that the command issued is not allowed during the mode that the monitor display is presently in, or is not available on this system. SOURCE (MODE) Press the (SOURCE) button on the remote or momentarily press the POWER button on the left side of the LCD screen to select the input signal AV1, AV2 (or the optional DVD player or Hard Disk drive, if installed). 14 © 2005 Directed Electronics, Inc. MENU (CONSOLE MENU) Press "MENU" button on the monitor or remote to activate the screen parameters set-up. The sequence of set-up items is as follows: FM SHARPNESS BRIGHTNESS CONTRAST SATURATION FM: Transmitting frequency BRIGHTNESS: Brightness adjustment SATURATION: Color saturation adj. HUE RESET SHARPNESS: Sharpness adjustment CONTRAST: Contrast adjustment HUE: Color hue adjustment RESET: Resets above (except FM) to factory default settings. Once the desired setting is selected, press the cursor buttons to adjust the setting. On the remote use the up/down cursor buttons located at either side of the menu button. On the monitor use the cursor buttons to the right side of the button. [. . . ] No Sound If acquiring signal from another remote device (e. g. DVD player or CD player) ensure the device is setup correctly. The DVD player is in pause, slow motion, fast forward, or fast reverse mode. type setting is correct for the monitors and DVDs being used. [. . . ]