User manual DEI OHV1202 Owners Guide

[. . . ] OWNER'S GUIDE INSTALLATION GUIDE 12" (16:9) Overhead Video Monitor MODEL OHV1202 © 2005 Directed Electronics, Inc. N81122 03-05 NON-TRANSFERABLE LIMITED ONE YEAR CONSUMER WARRANTY Directed Electronics, Inc. (Directed) promises to the original purchaser that the new automotive video monitor and/or source unit(s) (the Product) that is purchased and installed from a Directed authorized dealer more than ninety (90) days after the purchase of a new vehicle are warranted for a period of one (1) year from date of purchase of the Product. Directed promises to the original purchaser that all video accessories will be free from defects in materials and workmanship under normal use and condition for a period of ninety (90) days after the date of purchase. [. . . ] Remove old battery and replace it with a new battery (CR2025) with the positive "+" sign facing as shown above. Push battery holder back into its compartment until it is locked. PRECAUTIONS 1. Do not misuse battery by shorting the positive "+" and negative "-" terminal or put it into fire. Overheating may cause the battery to explode and cause a fire hazard. If the remote is not to be used for a long period, remove the battery from the remote to prevent damage from battery leakage. To avoid accidents, prevent children from playing with the battery. 12 © 2005 Directed Electronics, Inc. Operating the Monitor OPEN/CLOSE THE DISPLAY MONITOR To open the display monitor, push the "OPEN" button and pull the monitor down by the middle of the LCD to the desired position. Use the middle of the LCD screen to rotate to a desired viewing position. WARNING: THE LCD MONITOR MUST ALWAYS BE OPENED, CLOSED, OR POSITIONED FROM THE MIDDLE OF THE SCREEN AS SHOWN BY THE POINTING HAND BELOW. DO NOT USE THE CORNERS OF THE SCREEN, THIS CAN RESULT IN DAMAGE/LEAKAGE OF THE SCREEN. Open Button Clos ed Pos ition Use this portion of the screen for opening, closing, and positioning. Open Pos ition WARNING: DO NOT CLOSE THE LCD SCREEN IF A MEMORY CARD HAS BEEN INSERTED INTO THE DVD PLAYER. THIS CAN CAUSE THE LCD SCREEN TO BREAK OR LEAK FLUID. IF YOU SHOULD COME IN CONTACT WITH LEAKED FLUID, WASH THE AFFECTED AREA THOROUGHLY WITH WATER AND SEEK IMMEDIATE MEDICAL ATTENTION. REMOVE ALL MEMORY CARDS BEFORE CLOSING THE LCD SCREEN. To close the display monitor, first rotate the LCD screen to align for closure and then push the LCD screen up until it latches closed with an audible click. Note: The ignition key must be in the Accessory or Ignition position in order for the monitor to have power. © 2005 Directed Electronics, Inc. 13 Power Up/Down the Display Monitor The unit will power up when the display monitor is unlatched and pulled down. (If the unit does not power up, press the Power right side of the monitor. To turn the power off to the unit, press the POWER button on the remote. The power will also button on either the remote or the Power button on the shut Off when the display monitor is placed in the closed and latched position. If the hand icon or "INVALID KEY" displays in the upper left-hand corner of the screen when using the remote, it indicates that the command issued is not allowed during the mode that the monitor display is presently in, or is not available on this system. P (PICTURE-IN-PICTURE/SPLIT SCREEN) Select this feature by pressing on the remote or the P button on the monitor to display PIP or Split Screen viewing of a total of two inputs from the DVD, or the A/V inputs. When the system is in PIP or Split Screen mode, the source feature described below only works on the small inserted picture or on the split picture displayed on the right side of the monitor (if the optional DVD player is installed). NOTE: The switch on the HP200 headphones allow the listener to switch between the two pictures (PIP or Split Screen). The IR button on the remote turns the audio to the headphones On/Off. SOURCE (MODE) Press the (SOURCE) button on the remote or the S button on the monitor to select the input signal AV1, AV2 (or the optional DVD player or Hard Disk drive, if installed). 14 © 2005 Directed Electronics, Inc. MENU (CONSOLE MENU) Press "MENU" button on the monitor or remote to activate the screen parameters set-up. The sequence of set-up items is as follows: FM SHARPNESS BRIGHTNESS CONTRAST SATURATION FM: Transmitting frequency BRIGHTNESS: Brightness adjustment SATURATION: Color saturation adj. HUE RESET SHARPNESS: Sharpness adjustment CONTRAST: Contrast adjustment HUE: Color hue adjustment RESET: Resets above (except FM) to factory default settings. Once the desired setting is selected, press the cursor buttons to adjust the setting. On the remote use the up/down cursor buttons located at either side of the menu button. On the monitor use the cursor buttons to the right side of the button. If a button is not activated within 5 seconds, this function mode will turn OFF. [. . . ] Inspect the connecting cables for any fraying or breakage. No Sound If acquiring signal from another remote device (e. g. DVD player or CD player) ensure the device is setup correctly. The DVD player is in pause, slow motion, fast forward, or fast reverse mode. [. . . ]