User manual DELONGHI 182H

[. . . ] Keep instructions in a safe place. 2 DO NOT place clothes or other materials on the Heater, as apart from the danger of fire their presence could affect the efficient working of the appliance. ;;;; QQQQ 4 DO NOT position Heater close to chairs and fabrics DO NOT move Heater from room to room when it is lit. 3 5 DO NOT position Heater alongside a wall or near curtains, etc. ALWAYS face Heater towards centre of room. Special care shouold be taken if the Heater is on a surface where it can move or twist on its wheels or castors if knocked by a child or dog, etc. 6 A LEAK WILL SMELL IF a leak is suspected, turn the gas off at cilinder. [. . . ] Note: Quick-on is so designed as to prevent it from being fitted to the valve, unless the regulator handle is in the closed position; therefore, never attempt to mount or dismount it, if the handle is not in this position. OPEN Handle verically flamme On Handle horizontally flamme Off CLOSED fig. 3 Operation Once the Quick-on is correctly mounted on the valve, gas supply is possible by turning the regulator handle upwards (counterclockwise). To shut off the gas supply, reverse above procedure; an arrow engraved on the handle indicates the closing direction (fig. 3). Symbols engraved on the bonnet show how to operate the regulator handle. CAUTION: if you are unable, to open the regulator handle, this means that your Quikon is not correctly connected to the valve. Do not force the handle to open, instead start again the operations described above in 3. GAS OFF Replacement of a cylinder Make sure that: - all taps on the consuming appliance are in the closed position. - the Quick-on regulator handle is in the closed position. Then, dismount the Quick-on by pressing horizzontally on the handle ond pulling upwards at the same time (fig. 5). Do not attmpt to carry out this operation with the regulator handle in the open position. fig. 4 2 1 GAS OFF fig. 5 GENERAL SAFETY INSTRUCTIONS Type Category Execution Two burner models Three burner models Max. input Kw 3. 5 Kw 4. 2 g/h 254 g/h 305 Med. input Low input Kw 1. 8 g/h 131 g/h 109 Gas Pressure Gas combustion air quantity 7 m3/h See Rating label Kw 2. 85 g/h 207 Kw 1. 50 28-30 mbar 8. 4 m3/h this appliance is designed to operate with butane, at nominal pressure: 28÷30 mbar CYLINDER VALVE If heater does not competely extinguish, including pilot, when gas is turned off, do not remove regulator. Return valve to open position and leave heater alight, xhich is perfectly safe, until attend to by the gas supplier. Regulators, Hoses and clips Check that tubing is completely over the nozzles at each end of the tubing and that is held firmly in place by tube clips. Examine flexible tubing regularly and get your Dealer to fit new tubing 400 mm long if perished, worn or damaged. ATTAKS NATURAL RUBBER-USE ONLY TUBING TO B. S. Avoid dending or constricting the rubber tube when the pressure regulator is connected to the gas cylinder. 3016 SET AT 28 MBAR (11. 2 IN W. G. ) for butane must de connected to the appliance with the above tubing, using suitable tube clips. VENTILATION USE ONLY IN A WELL VENTILATED ROOM Adequate ventilation must be provided in rooms in which the heater is used. This ensures removal of the products combustion and allows the entry of replacement air. Adequate ventilatio should considerably reduce the possibility of condensation accurring. The following table shows the smallest size of room suitable for each heat setting and the ventilation which must de provided. The heater may used for short periods in smaller rooms. § TWO BURNER MODELS Room Room Size Aperture 18 m3 THREE BURNER MODELS Room Room Size Aperture 15 m3 Heating Setting MIN MED 87. 5 cm2 28. 5 m3 105 cm2 MAX 35 m3 42 m3 MAINTENANCE Ensure that the heater is kept free of dust. When the heater should be covered and stored in a dust-free place. Stains on the exterior should be removed with soapy solution when the heater is cold. [. . . ] Continue to fully depress the knob for a further 10 seconds to allow the thermocouple probe to heat up, then turn the knob to the required heat setting. CONTROL OF THE HEAT INPUT: For low input - leave control knob in position (small flame) For medium input - slightly depress knob and rotate to position (medium flame) For full input - slightly depress knob and rotate to position (big flame) TURNING-OFF THE HEATER The heater will only be totally "OFF" when the supply of gas from the cylinder has been turned "OFF" after use the appliance must be turned "OFF" at the valve. Turn the regulator gas switch clockwise to the position (Model No. 634) GAS OFF DO NOT ATTEMPT to relight until FIVE minutes have elapsed. WARNING FOR SWITCH-ON SYSTEM: When the heat is alight, NEVER turn the switch on the cylinder to the disconnect position. [. . . ]