User manual DELONGHI CONTACT-GRILL CGH800

[. . . ] WARNING: Very carefully dispose of the cut off plug after removing the fuse: do not insert in a 13 Amp socket elsewhere in the house as this could cause a shock hazard. With alternative plugs not incorporating a fuse, the circuit must be protected by a 15 Amp fuse. WARNING - THIS APPLIANCE MUST BE EARTHED IMPORTANT The wires in the mains lead are coloured in accordance with the following code: Green and yellow: Earth E Blue: Neutral L Brown: Live N If the plug is a moulded-on type, the fuse cover must be re-fitted when changing the fuse using a 13 Amp Asta approved fuse to BS 1362. In the event of losing the fuse cover, the plug must NOT be used until a replacement fuse cover can be obtained from your nearest electrical dealer. [. . . ] For repairs to the cord, contact your local authorised Service Agents. - Do not unplug the appliance by pulling the supply cord. - Only switch the appliance on with the grill plates fitted. - WARINING: charcoal or similar combustible fuels must not be used with this appliance. - Do not immerse the appliance in water. - Allow the appliance to cool down completely before storing it away. - Do not use sharp tools on the grill plates as these may damage the non-stick coating. This appliance conforms to EEC Directive EN 55014 regarding the suppression of radio disturbance. INSTALLING THE GRILL - Before using the grill, make sure that it has not been damaged in any way during transportation. - Place the appliance on a flat surface well out of the reach of children, as high temperatures are generated during use. - Before plugging the appliance into the mains , check that: the supply voltage corresponds to that indicated on the rating plate fitted on the appliance; the power on the mains socket is minimum 10A; the mains socket is suitable for the type of plug fitted on the appliance; if not it should be changed; the mains socket is earthed. The manufacturer does not accept any liability for damage caused as a result of non-compliance with this requirement. - Before using the grill for the first time, switch it on and leave it to heat up in the barbecue/party grill position (pos. 2) without any food, for at least 5 minutes; open the window in order to eliminate any unpleasant smell that tends to be given off when an appliance is new. 5 INT 22-09-2003 9:20 Pagina 6 USING THE APPLIANCE - Plug into the mains socket and adjust the thermostat (H) to the required position. Pre-heat the appliance with the grill plates closed. - When the appliance has reached the required temperature, the "READY" indicator light (I) come on. - Place the food to be grilled on the grill plates. - Place the fat collection receptacle (N) under the fat drainage spout. - To turn the appliance off, turn the thermostat knob anticlockwise until it stops and unplug from the mains socket. - After cooking, unplug the appliance and leave to cool. - The release catch (B) enables the appliance to be closed (position 1) for easy transport. - The appliance has a hinged top plate to adapt to foods of any thickness. Never touch the plates with sharp implements as this could damage the coating. COOKING TIPS - Thawed and marinaded meat should be dried thoroughly before being placed on the grill. - Meat should be seasoned before grilling but salt should be added at time of serving. [. . . ] WARNING - THIS APPLIANCE MUST BE EARTHED IMPORTANT The wires in the mains lead are coloured in accordance with the following code: Green and yellow: Earth E Blue: Neutral L Brown: Live N If the plug is a moulded-on type, the fuse cover must be refitted when changing the fuse using a 13 Amp Asta approved fuse to BS 1362. In the event of losing the fuse cover, the plug must NOT be used until a replacement fuse cover can be obtained from your nearest electrical dealer. The colour of the correct replacement fuse cover is that as marked on the base of the plug. B) If your appliance is not fitted with a plug, please follow the instructions provided below: As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The green and yellow wire must be connected to the terminal in the plug marked with the letter E or the earth symbol or coloured green or green and yellow. [. . . ]