User manual DELONGHI CTF2134S TOASTER

[. . . ] Ventilate the room during this operation. · Insert the slices of bread into the bread toasting slots and lower the control lever until it is all the way down. When the control lever is depressed, the flaps on the top of the bread toasting slots will close and the fan, which allows faster toasting, will switch on to maintain cooler touch sides even after several toasting cycles. In order to keep the toaster cooler touch, the fan will continue to operate for another minute even if the toaster has been switched off. [. . . ] · The plastic bag in which the appliance was packaged should be kept out of reach of children as it poses a suffocation hazard. · In order to remove the dust that may have accumulated on the appliance, simply dust it off with a soft cloth. · Before inserting the plug into the electrical socket, make certain: - The voltage of the socket corresponds to the value indicated on the information label, attached to the appliance. - The electrical socket is adequately earthed, the manufacturer declines any responsibility for the lack of observation of this norm. CTF2134C/S Toaster 4 Reheat function Press down the control lever and press the reheat button. The reheat light will remain on while the reheat function is in use. Please note that this is a fixed reheat time that cannot be adjusted by the browning control. Defrost function You may toast slices of frozen bread by pressing the defrost button immediately after having lowered the control lever; the toasting cycle will be lengthened in order to achieve the desired toasting level. The red warning light will remain lit while the defrost function is in use. Bagel function The "Bagel" function allows for the toasting of muffins, bread etc. Muffins must first be sliced in half and inserted with the cuts sides facing out; lower the lever and press the Bagel button. The red warning light will remain lit while the Bagel function is in use. "WARMING RACK" device Use this device to heat food. · Fasten the rack to the appliance by first inserting the hooks L and then clicking in the hooks, as shown in the Figure on page 2. (1-2), muffins or already toasted items. · Turn the browning control dial to the desired position. · Press down the control control lever until it clicks into place. · If the food is not warm enough, next time select a darker level of toasting. Hints and Tips for better toasting · If your toaster is not plugged in and switched on, the control lever will not lock in the down position. · For best results use bread slices of even thickness, size and freshness. Select a lower setting if: a) using stale bread (toasts more quickly than fresh bread) b) using thin bread (toasts more quickly than thick bread) · To remove smaller items such as muffins, crumpets and bagels the control lever can be lifted approximately 20mm above the starting position. · To achieve even browning, we suggest a minimum of 30 seconds between each toasting to allow the control to automatically reset. 5 CTF2134C/S Toaster · In the case of incompatibility between the socket and the plug of the appliance, have it replaced by a qualified technician. The use of adapters, multiple socket units and/or extension cables is not recommended. Whenever it may be necessary to use such equipment, it is advisable to use only single or multiple adapters or extension cables which comply with the current safety standards, and make sure not to exceed the wattage limit of the adapter or extension cable. · When the appliance is plugged into the electrical socket and whilst switched on never place hands into the bread toasting slots. · Never allow the appliance to be used by children or used without adult supervision. · Do not touch the appliance with wet or damp hands. · The areas surrounding the bread slots become very hot during use: operating the toaster should be carried out touching only the plastic controls. [. . . ] When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains lead clamp on the plug. If your electricity supply point has only two pin socket outlets, or if you are in doubt, consult a qualified electrician. Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified electrician and should only be replaced with a flexible cord of the same size. [. . . ]