User manual DELONGHI DE40P

[. . . ] This unit can be conveniently moved from room to room within your home and set-up in just minutes. I M P O R TA N T S A F E G U A R D S Read all instructions before using this dehumidifier. To reduce the risk of fire, electric shock, or injury to persons when using your dehumidifier follow basic safety precautions, including the following: 1) After transporting the appliance, wait 1 hour before using it. 2) Do not store or use gasoline, oil, sulphur or other flammable vapors and liquids in the vicinity of this or any other appliance. Do not install the appliance near source of heat. [. . . ] From 0 -10 the hours increase by 30 min. and from 10-24 the hours increase by 1 hour increments. button With the appliance switched ON, if you press the TIMER button the display will show the hours after which you want the appliance to switch OFF (1-2-3. . . With the appliance in the STAND-BY position, if you press the TIMER button the display will show the hours after which you want the appliance to switch ON (1-2-3. . . hours ). MODE TURBO PUMP button Press this button to select the Fan only or Dehumidifier modes. POWER button Use this button to activate the "turbo power" function. In this mode, the appliance will operate at maximum fan speed and in continuous mode. If pressed again, the unit will revert back to previous settings. button (only on pump models) Use this button to activate the heavy-duty pump system for active drainage. 5 ENGLISH Display lights ON light When the STAND-BY button is pressed to start the unit, the ON light will come on automatically. The light will go off again when the unit is switched off. NOTE: After a power outage, the unit will not switch itself on again automatically. When the power supply has been reestablished, please press the STAND-BY button to start the unit again. TANK Warning light If the water tank is full, improperly positioned or missing, the tank warning light will start blinking. An alarm will sound until the tank is either emptied or correctly positioned into place. DEFROSTING light With an ambient temperature of less than 15°C, (59°F) the appliance performs defrosting cycles. While the appliance is defrosting, the defrosting light comes on and remains on until defrosting is completed. Condensed water can be drained via a hose connected to the outlet located in the lower part of the tank proceeding in the following way: 1. Using a 5 mm drill bit, (0. 2 inches) drill a hole in the base of the tank along the torus as shown in figure 2. Connect a hose to the hose connector (fig. Make sure that the hose is not higher than the hose connection (see figure 4). NOTE: When you remove the rubber cap keep it in a safe place in case you want drain into the tank. C) Continuous draining using the pump (only on pump models) The exclusive heavy-duty pump system allows water removal of up to 13. 12 feet (4m) in height. If you want the water to flow directly to a drain, connect the condensation discharge tube supplied to the connection pipe located on the lower part of the unit (Fig. Select the dehumidifying function and press the PUMP button. Drill fig. 4 Drain Note: With the condensation discharge hose missing and the pump switched ON, the pump light will start blinking and the appliance will be in the stand-by position. To eliminate this problem insert the hose and switch the pump button ON. The condensation hose can be discharged into a drain. [. . . ] 2) The turbo power function is an automatic dehumidification function that is used when you wish to operate the appliance at maximum power. When in this mode, the display will show on the left side (two dots) and on the right side the room humidity present. To stop the turbo power function, simply press the button again. to program the delayed start function: From the OFF Position 1) With the unit OFF, press the button and use the button to set the number of hours after which the appliance should start functioning. 2) On the left side the display will show the number of hours after which the appliance should start the operation (1-24h) and a small dot under the symbol indicates that the timer function has been selected. [. . . ]