User manual DELONGHI DEHUMIDIFIER DEC180E

[. . . ] 4. Control panel Control panel cover Air outlet grille Condensate collection tank Description 5. 8. Lifting handle Air intake grille Electrostatic filter (some models only) Air filter Accessories condensate drain hose (some models only) rubber bung 14 Warnings Warni ngs · Use this appliance only as described in this instruction manual. As with all electrical equipment, whilst the instructions aim to cover as many eventualities as possible, caution and common sense should be applied when operating and installing this appliance. · This appliance is designed to dehumidify residential environments and must not be used for other purposes. [. . . ] · The power socket and electrical circuit are adequate for the appliance. · The power socket matches the plug. If this is not the case, have the plug replaced by a qualified electrician. · The power socket must be adequately earthed. 15 ENGLISH Installation Inst ructions for fitting the wheels 1) Make sure the appliance is unplugged from the mains and the tank is empty 2) Remove the rubber caps from the base of the appliance by pulling them out, using pliers if necessary (see Figure 1/1). 3) Fit the wheels by inserting the shafts into the holes (see Figure 1/2) Note: When performing these operations, make sure the appliance is not tilted over 45°; in any case, after fitting the wheels, wait at least one hour before using the appliance again. Installation Position the appliance in the room to be dehumidified: A free space of at least 50 cm must be left at the front of the humidifier, so as not to block the air outlet. A space of around 5-10 cm should be left at the rear of the appliance for aeration. Condensate can be drained in one of two ways: A) Draining into the tank The condensate can be drained directly into the tank located inside the appliance (fig. The tank can be easily removed and has a handle making it simple to carry and empty. 1 B) Continuous external draining If the appliance is to be operated for long periods of time but you are unable to empty the tank, you are recommended to use the continuous drain facility. 1) Drill the inside of the drain spout using a 7 mm dia. drill bit or removing the precut section by pressing with a screwdriver or similar (Fig. For models without drain hoses supplied, we suggest you purchase a rubber hose around 1 m long, with an internal diameter of 9. 5 mm. 3) The condensate drain hose must under no circumstances slope upwards, otherwise the water may remain in the tank. Check there are no kinks in the hose (Fig. You will need it to plug the hose or close the spout if you revert to draining into the tank (see point A). 4 NO YES 16 How to dehumidify Hygrometer/thermometer button Display Timer ON indicator light ON/OFF button Decrease humidity/hours button Max. power indicator light Power level button Increase humidity/hours button Dehumidifying indicator light Ventilation indicator light MODE button COMFORT button Timer button Comfort indicator light "ON/OFF" Starts the appliance. button "MODE" button Selects the "dehumidification" function or the "ventilation" function. "COMFORT" button Activates the "COMFORT" function When the "COMFORT" function is activated, pressing the button again deactivates it. 17 ENGLISH Temperature indicator light Humidity percentage indicator light The buttons "POWER LEVEL" button Selects the power level (MIN/MAX). Hygrometer/thermometer Ti mer button button Displays, in sequence for 2 secs. , the ambient humidity, with a tolerance of +/- 5% (" " light flashing) and the ambient temperature, with a tolerance of +/- 1% ("°C" light flashing). Sets the number of appliance operating hours (maximum 24). Increase/decrease Di splay humidity/hours Adjusts the desired humidity level in 5% steps and sets the timer. Meaning of the codes that may be shown on the display: 1. "dF" Indicates that the appliance is in Standby mode. Indicates that the appliance is operating in "COMFORT" mode. Indicates that the tank is not fitted, is full or is positioned incorrectly. Indicates that the appliance is operating at low temperature. [. . . ] If it does not fit your socket, the plug should be cut off from the mains lead, and on appropriate plug fitted, as below. warning: Very carefully dispose of the cut off plug after removing the fuse: do not insert in a 13 Amp socket elsewhere in the house as this could cause a shock hazard. With alternative plugs not incorporating a fuse, the circuit must be protected by a 15 Amp fuse. If the plug is a moulded-on type, the fuse cover must be re-fitted when changing the fuse using a 13 Amp Asta approved fuse to BS 1362. [. . . ]