User manual DELONGHI HCA 330TS/W

[. . . ] In order to wall mount your convector please proceed as follows: 1. Fix two brackets "A" following carefully the dimensions as indicated in decsription. Use a 6 mm masonry drill and suitable wall plugs and 2 x No 8 screws (minimum lenght 25 mm). Hang the convector on the two brackets fixed to the wall and insert metal brackets "B" into the bottom rear section of the base of the convector as indicated in figure 1, one at each end. [. . . ] 4) to the desired comfort temperature from (5°C) and MAX (35°C). If the selected temperature is higher than the actual room temperature, the appliance will start automatically and rapidly heat the room until it reaches the selected temperature. The unit will automatically maintain the temperature at a constant level by cycling between max power, med power and min power as it approaches the selected comfort temperature (see fig. 5). * D Press four times OFF 6. Maximum power example (fig. 5) Fig. 3 Display LEDs Selected Power Power used MAX MAX MED MIN OFF Cycles between Fig. 4 Electric Heating Convector HCA 4 If the room temperature exceeds the selected temperature level, the appliance will switch off (fig. 3D). The heater will switch back on automatically when the room temperature falls below the selected temperature level. If medium power level has been selected using the button, and the thermostat set, the heater will modulate between the medium and minimum power levels. As with the maximum power setting, if the room temperature exceeds the selected temperature, the appliance will switch off, and then on again when the temperature falls. (For models with timer, ensure that the switch on the timer dial (as shown in description) is in position 1, manual. NOTE: if the timer switch is at the 0 position (fig. 4), the heater is off and will not operate). Frost stat function Press the button, it is recommended to select maximum power level. Set the thermostat dial to the " " position (fig. When set in this way, the appliance will switch on automatically only if the room temperature falls below 5°C, to prevent freezing, at minimum energy consumption. This function is not guaranteed in the event of power failures, even if lasting just a few seconds. * Models with turbo fan boost (as shown in decsription) A number of models have a turbo fan boost for even more rapid and uniform heating. To use this function, press the switch on the fan grill. Cool air ventilation To operate the fan only for "cool air" ventilation, ensure that ECC is off and turn the thermostat to the maximum then press the switch on the fan grill. Using the timer If you wish to use the timer, position the switch in the middle position (Fig. 5) 1= Manual (timer override) = Timed operation 0 = Heater off Fig. 5 Setting the correct time Check the time on your watch. (16. 00), turn the dial in a clockwise direction until the number 16 5 Electric Heating Convector HCA is lined up with the triangular pointer . N. B. : Never turn the dial in an anti-clockwise direction!The timer is in effect, an electric clock and works only if the plug is connected to the power supply. Whenever the plug is disconnected or there is a power failure, the clock must be re-set. 21 20 19 16 pointer To program the timer 1) Set the operating times by pushing out the notches on the dial corresponding to the period required (each notch represents 15 mins. ) 2) Make sure that the timer indicates the correct time (see instructions on setting the correct time). 3) Select the desired function as shown in the table on page 5. Once programmed in this way, the appliance will repeat the preestablished program every day, if the selector is in the position Fig. 6 operating time 21 20 19 16 Timer override If you wish to override the timer settings, push the timer switch to position 1 (as shown in description) manual (timer override). To return to timed operation push the switch back to the middle position (as shown in description). Maintenance Before carrying out any maintenance, unplug the heater from the mains and wait for it to cool. The convector requires no particular maintenance. It is sufficient to remove the dust with a soft, dry cloth. [. . . ] - As with any electrical appliance, whilst the instructions aim to cover as many eventualities as possible, caution and common sense should be applied when operating your appliance, particularly in the vicinity of young children. 7 Electric Heating Convector HCA Electrical connection (U. K. only) A) Your appliance comes fitted with a plug, it will incorporate a 13 Amp fuse. If it does not fit your socket, the plug should be cut off from the mains lead, and an appropriate plug fitted, as below. WARNING:Very carefully dispose of the cut off plug after removing the fuse: do not insert in a 13 Amp socket elsewhere in the house as this could cause a shock hazard. [. . . ]