User manual DELONGHI IH

[. . . ] ALWAYS face heater towards centre of room. Special care should be taken if the heater is on a surface where it can move or twist on its wheels or castors if knocked by a child or dog, etc. Minimum Clearance : 200 mm from sides, 1500 mm from front. The heater you have purchased is fitted with safety devices which come on in the event of malfunctioning while the appliance is in use. [. . . ] When connecting the pressure regulator to the gas bottle avoid undue twisting of the flexible tubing. A 28 ÷ 30 mbar (11. 2 in w. g. ) pressure regulator for Butane or Propane complying to local standard must be connected to the appliance with the above tubing, using suitable tube clips. fig. 6 Room ventilation USE ONLY IN A WELL VENTILATED ROOM Adequate ventilation must be provided in rooms in which the heater is used. This ensures removal of the products of combustion and allows the entry of replacement air. The following table shows the smallest size of room suitable for each heat setting and the dimensions of the aperture which must be provided equally divided between high and low level. Control knob setting Position small flame (low rate) Position medium flame (medium rate) Position big flame (maximum rate) Room Size IH-IHF 15 m3 Room Size IH2-IHF2 Room Aperture 28. 5 m3 42 m3 105 cm 2 42 m3 SAFETY GUARD The guard is to prevent risk of fire and no part of it should be permanently removed. It does not give full protection for young children or the infirm. 4 OPERATING INSTRUCTIONS MODEL IH-IHF Lighting the heater 1. FROM « » POSITION, fully depress the control knob for 10 seconds and turn to (Small Flame) position. (If pilot flame does not ignite return to starting position and repeat). Continue to fully depress the knob for a further 20 seconds to allow the thermocouple probe to heat up. Then turn the knob to select the desired setting as follows: (Small Flame) Low Input (Medium Flame) Medium Input, (Big Flame) Maximum Input Auxiliary ignition Should piezoelectric starter fail to work, repeat operation on control knob and use a match to light pilot flame and repeat the operations above described. Turning off the heater Turn off the gas bottle tap. The Heater will be totally "OFF" only if the tap at the gas bottle is turned off. OPERATING INSTRUCTIONS MODEL IH2-IHF2 Lighting the heater 1. Depress the button for 10 seconds, consequently depress button two or three times (If pilot flame does not ignite return to starting position and repeat). Continue to fully depress button for a further 20 seconds to allow the thermocouple probe to heat up then release. To light up the 3 burners, turn the thermostat fully counter-clocwise to the max. When the room temperature has reached the desired level, turn the thermostat clock-wise until the side burners light off. The thermostat will now automatically maintain the temperature at the desired level changing between max. power (all the three burners are on) and min. power (only one burner is on). Auxiliary ignition Should piezoelectric starter fail to work, repeat operation on control knob and use a match to light pilot flame and repeat the operations above described. Turning off the heater To turn the heater off, turn the thermostat to "" position, then turn off the gas bottle tap. The heater will be totally "OFF" only if the tap at the gas bottle is turned off. Important When the operating button" " is left at the end of the starting time (see also rating plate), this must move up about 5 mm and return to his starting height. If this does not happen, shut the gas valve and contact your aftersales service centre. Do not let the appliance work with the operating knob pressed downwards by force. 5 VENTILATED RADIANT HEATER Electrical connection Before using the appliance check that your supply voltage is the same as that shown on the rating label of the unit. [. . . ] Contact your nearest Technical Assistance Service if the fan heater does not start operating normally again. Ñever direct the fan hater's air flow towards furniture, curtains , spray cans and inflammable material. MAINTENANCE Wipe your appliance with a soft damp cloth and only when it is switched off, cold and unplugged. Do not use solvents or abrasives detergents. Check that there is no dust blocking the air inlet or outlet grids. [. . . ]