User manual DELONGHI IHREGCE ROSSO

[. . . ] For a regular gas combustion the required air quantity is: 8, 4 m3/h. WARNINGS ALWAYS use heater in accordance with instructions. Read the instructions book carefully and keep it in a safe place. This appliance requires a rubber tube and a pressure regulator in accordance with the law in force. If not supplied check with your gas supplier. [. . . ] Changing of gas bottle must not be carried out in the presence of a naked flame. Use the gas bottle always in upright position. If a screw on regulator is used ensure that the regulator washer is present and in good condition -replace if in any doubt. To place the bottle in position, remove the rear panel which faces the inside during transport, by unfastening the screws; than put the bottle in position and replace the panel. Pressure regulators, rubber tubes and clips CHECK that tubing is completely over the nozzles at each end of the tubing and that it is held firmly in place by tube clips (See fig. 5). Examine flexible tubing regularly and get your Dealer to fit new tubing 400 mm long complying to local standard, if perifig. Ensure that the rubber tube inserted in the plastic support (see fig. When connecting the pressure regulator to the gas bottle avoid undue twisting of the flexible tubing. A 28 ÷ 30 mbar (11. 2 in w. g. ) pressure regulator for Butane or Propane complying to local standard must be connected to the fig. 6 appliance with the above tubing, using suitable tube clips. Room ventilation USE ONLY IN A WELL VENTILATED ROOM Adequate ventilation must be provided in rooms in which the heater is used. This ensures removal of the products of combustion and allows the entry of replacement air. The following table shows the smallest size of room suitable for each heat setting and the dimensions of the aperture which must be provided equally divided between high and low level. Control knob setting Position small flame (low rate) Position big flame (maximum rate) Position medium flame (medium rate) Room Size Room Aperture 15 m3 42 m3 105 cm 2 28. 5 m3 SAFETY GUARD The guard is to prevent risk of fire and no part of it should be permanently removed. It does not give full protection for young children or the infirm. 4 OPERATING INSTRUCTIONS Lighting the heater 1. FROM «G» POSITION, fully depress the control knob for 10 seconds and turn to (Small Flame) position. (If pilot flame does not ignite return to starting position and repeat). When the pilot flame is lit, continue to fully depress the knob for a further 20 seconds to allow the thermocouple probe to heat up. Then turn the knob to select the desired setting as follows: (Small Flame) Low Input (Big Flame) Maximum Input (Medium Flame) Medium Input, Auxiliary ignition Should piezoelectric starter fail to work, repeat operation on control knob and use a match to light pilot flame and repeat the operations above described. Tunring off the heater Turn off the gas bottle tap. The Heater will be totally "OFF" only if the tap at the gas bottle is turned off. Important When the large knob is released at the end of the ignition time (see the rating plate and instruction booklet), it must return upwards by around 5 mm to its initial position. If this does not happen, close the gas tap and contact your after-sales service centre. Never operate the appliance with the large knob held downwards by force. VENTILATED RADIANT HEATER TENSION FREQUENCY 50Hz AMPS MAXIMUM POWER 2000W 220-230V 9, 0A Electrical connection - Before using the appliance check that your supply voltage is the same as that shown on the rating label of the unit. [. . . ] - Never direct the fan hater's air flow towards furniture, curtains , spray cans and inflammable material. - Do not install the appliance in a room which might contain gas, oil or sulphur, or near sources of heat. CAUTION: In order to avoid a hazard due to inadvertent resetting of the termal cutout, this appliance must not be supplied through an external switching device, such us a timer, or connected to a circuit that is regularly switched on and off by the utility. MAINTENANCE Wipe your appliance with a soft damp cloth and only when it is switched off, cold and unplugged. Do not use solvents or abrasives detergents. [. . . ]