User manual DELONGHI PAC 30

[. . . ] The PAC 30 ELECTRONIC can also be used as a heater during the winter months. The PAC 30 ELECTRONIC sets the temperature automatically. TECHNICAL DATA WATER FUNCTION - AIR FUNCTION Power supply voltage Frequency * Cooling capacity Cooling capacity Electric power consumption Max. power consumption (heating mode) Air flow capacity Timer Dimensions: width height depth Net weight (mm) (V) (Hz) (Frig/h, W, Btu/h) (Frig/h, W, Btu/h) (A) (W) (m /h) 3 Tab. 1 see rating label " " " " " " 360 24 h 560 725 365 44 Max. power consumption (air-condit. mode) (W) (kg) Technical data subject to change without prior notice * According to standard ASHRAE 128P NB. When indoor temperature exceeds 32°C, the appliance should be operated with water. IDEAL OPERATING CONDITIONS (AIR-CONDITIONING FUNCTION) ROOM TEMPERATURE ROOM HUMIDITY FACTOR FREQUENCY POWER SUPPLY VOLTAGE see rating label 21 ÷ 32°C BELOW 80% see rating label Tab. 2 19 DESCRIPTION OF MAIN FEATURES Tab. 3 Air outlet grid Control panel Programmer (timer) Water container Castors Castor stops Water collecting tray Water container compartment door Air filter Air intake grid Warranty envelope Exhaust hose compartment Power cable compartment Handle Water collecting tray drainage tube 20 DESCRIPTION OF ACCESSORIES DESCRIPTION Tab. 4 PARTS SUPPLIED Exhaust hose 1 Stopper + flange 1 Castor stop 2 De-scaling fluid 1 Window nozzle 1 Suction cup set 1 ACCESSORY CHECK Check that all parts listed in Table 4 are included. 21 INSTALLATION FOR AIR-CONDITIONING FUNCTION Our air-conditioner is portable and versatile: it can be used as a permanent installation or wise easily moved from one room to another. The appliance must be fitted at least 30 cm. from the surrounding walls. 30 cm 30 cm When installed permanently, all air discharged from the rear hose is extracted from the room in which the PAC 30 ELECTRONIC is installed. [. . . ] seawater or water treated using softening systems that utilize kitchen salt. 24 AIR COOLING FUNCTION If the air cooling function of PAC 30 ELECTRONIC is chosen, it is sufficient not to fill the water container. FINAL CHECK In order to obtain maximum performance from your air-conditioner, make sure that: -- doors and windows in the room to be air-conditioned are closed (with the sole exception of the partially opened window necessary for "temporary" installation) Close the windows Close the doors Draw the curtains Lower the blinds -- the room is well shaded from direct sunlight by drawing curtains and/or partially lowering blinds or shutters, to avoid excessive energy consumption -- the intake and outlet vents are free of any obstruction at all times -- there are no sources of heat in the room. Do not cover THE AIR-CONDITIONER IS NOW READY FOR USE, so let's now take a look at the controls. 25 CONTROL PANEL Signal lamp indicating 3 min. wait (flashing) or air-cooling (on continuously) Min. speed warning light ON/OFF Timer key ON timer signal lamp Economic heating signal lamp Max. heat warning light Automatic heating signal lamp Temperature OK signal lamp Automatic air-cooling signal lamp TIMER ON MEMO CONTROL THERMOSTAT Timer Heating signal lamp Thermostat cursor Air-cooling signal lamp Button ON/OFF Automatic position key Heating key Plot lamp mains (continuous light) or malfunction (flashing light) Air-cooling key SETTING THE TIMER The programmer/timer, like all clocks, must be set to the exact time. (16. 00), turn the dial in a clockwise direction (following the direction of the arrow) until the number 16 is lined up with the triangular pointer (the arrows indicates 4:00 P. M. approximately ). PROGRAMMED MODE 1) Select the desired function as shown in the chart overleaf. 2) Press the TIMER key, the "TIMER ON" signal light will come ON. 3) Make sure that the timer indicates the correct time (see instructions on setting). Operating time Funzionamento 21 20 19 16 21 20 19 16 N. B. : Never turn the dial in an anti-clockwise direction!The timer is in effect, an electric clock and works only if the plug is connected to the power supply. Whenever the plug is disconnected or there is a power failure, the programmer stops (the clock is then "slow") and must be re-set. The Pinguino can be used for either AIR-COOLING or HEATING. The unit can be used in either programmed or nonprogrammed mode. 4) Set the operating times by pushing out the notches on the dial corresponding to the period required (each notch represents 15 mins. ) The unit will now switch on and off each day at the selected times. N. B. : To override the programmed operating times, simply press the ON/OFF key (the timer signal lamp ON will go out) NON-PROGRAMMED MODE 1) Press the TIMER ON key again, the TIMER ON signal lamp will go out). 2) Select the desired function as shown in the chart on pg. For technical reasons, the temperature is not expressed in degrees but by a line increasing in thickness. We therefore recommend that when starting up the appliance, the thermostat be turned to maximum (thick green line = maximum cold, thick pink line = maximum hot). When the desired temperature has been reached, move the cursor slowly away from the maximum cold or maximum hot position until the appliance is switched off by operation of the thermostat. In this way the appliance has been programmed with the exact temperature degree required, which is then maintained automatically by the thermostat. This appliance is fitted with a safety device that blocks its operation if at least 3 minutes have not elapsed from when it was last switched off. 26 HOW TO START UP THE CONDITIONER (see control panel on the opposite page) Plug the appliance into the mains. The signal lamp will come on . Press the ON/OFF key. [. . . ] Pour 1/4 liter of de-scaling fluid and 1 l clean water into the collecting tray situated under the container, at the bottom of the unit. c) Leave the air-conditioner to operate for about half an hour. d) Drain away all the fluid left in the tray and rinse thoroughly. The drainage tube should be open and the appliance switched on during draining. [. . . ]