User manual DELONGHI PAC 35

[. . . ] 4) Using a 24mm spanner, unscrew the union on the coupling. spanner to block the extrimity of the hose in position. Repeat this operation for the second union. b) Through a small hole (5. 5 x 2. 5 cm. ) in the lower part of the door or window frame. In this case, it is necessary to use the special frame for the connection hose. Frame for hose 5) Detach the condensation hose from its coupling. [. . . ] In the event there is still some condensation to be eliminated and the equipment is connected to its electrical feed, the waste pump may turn on spontaneously to get rid of that excess moisture even if the equipment itself has been turned off. The external unit should be protected from the elements (rain, snow, sun, etc. ). Rubber cap The external unit can also be mounted on a wall. In this case, use the special wall-mount brackets. Ring Coupling Washer Castor 20 ELECTRICAL CONNECTIONS Before plugging the unit into the mains, check the following: · the mains voltage must be the same as the voltage shown on the rating plate · the power socket and the mains circuit must be suitable for the power requirements of the unit · the socket must be suitable for the plug; if not, have the socket replaced · the power socket must be properly earthed. The manufacturer declines all responsibility for any damage or injury arising from nonobservance of this safety requirement. This appliance is manufactured in compliance with EEC Directive EN 55014 regarding the suppression of radio interference. · Draw the curtains and/or partially close the blinds to protect the room against direct sunlight. This will increase the efficiency and economy of the air-conditioner. · Do not place objects of any kind on the airconditioner. · Ensure that the air intake and discharge vents are not obstructed. · Make sure that there are no sources of heat in the room. FINAL CHECK In order to ensure that your air-conditioner operates with the maximum efficiency, make sure that: · all doors and windows in the room to be airconditioned are closed (except for temporary installation, in which case a window must be left partially open). Close the doors Lower the blinds Close the windows Do not cover YOUR AIR-CONDITIONER IS NOW READY FOR USE. Draw the curtains 21 CONTROL PANEL ON/OFF button ON/OFF pilot light A B C "Alarm" pilot light Timer ON/OFF pilot light Timer notches Thermostat Timer ON/OFF button Selecting fan speed button SETTING THE TIMER The programmer/timer, like all clocks, must be set to the exact time. (16. 00), turn the dial in a clockwise direction (following the direction of the arrow) until the number 16 is lined up with the triangular pointer (the arrows indicates 4:00 P. M. approximately ). PROGRAMMED MODE 1) Release B TIMER button 2) Set the operating times by pushing out the notches on the dial corresponding to the period required (each notch represents 15 mins. ) 3) Check that the timer indicates the correct time (see instructions on setting). Operating time Funzionamento 21 20 19 16 21 20 19 16 arrow pointer Note: Never turn the dial in an anti-clockwise direction!The timer is in effect, an electric clock and works only if the plug is connected to the power supply. Whenever the plug is disconnected or there is a power failure, the programmer stops (the clock is then "slow") and must be re-set. The unit can be used in either programmed or nonprogrammed mode. 4) Select the desired function as shown in the chart overleaf. The unit will now switch on and off each day at the selected times. Note: To override the programmed operating times, simply press the ON/OFF key. NON-PROGRAMMED MODE 1) B TIMER button must be pressed 2) Select the desired function as shown in the chart on the following page. Note For technical reasons, the temperature is not expressed in degrees but by a line increasing in thickness. We therefore recommend that when starting up the appliance, the thermostat be turned to maximum (thick green line = maximum cold). When the desired temperature has been reached, turn the thermostat slowly away from the maximum cooling position until the appliance switches off. The air-conditioner is now programmed to maintain the exact temperature at all times. 22 HOW TO START UP THE CONDITIONER (see control panel on the opposite page) Plug the appliance into the mains. Select the "programmed" or "non programmed" mode (see previous page) Select the fan speed required pressing "Fan speed" key C. AIR-CONDITIONING Key A ON/OFF (Conditioning) must be released Turn the thermostat to Max. [. . . ] · Do not place hot or heavy objects on the appliance. · Clean the air filter at least once weekly. · The appliance should be transported in the upright position or placed on its side. Empty the condensation tray before transporting the appliance. [. . . ]