User manual DELONGHI PAC 49RH

[. . . ] If you have any doubts check with a qualified electrician. · Avoid using extension leads with the unit. · Before cleaning or maintenance operations, always unplug the unit from the socket. · Do not pull on or place strain on the power cable when moving the appliance. [. . . ] Carefully hold the panel in the centre and lower to its closed position. During the "water functioning" operation and in particularly silent locations (eg the bedroom) a slight gurgling sound may be heard. IN HIGH HUMIDITY CONDITIONS Water is extracted from the air in the room, this water is also used to cool the condenser. When the humidity is particulary high an excess of water may buid up in the internal tank. This can be drained by removing the bung from the drain hose 10 and draining into a suitable receptacle. IMPORTANT: if the room temperature is 32°C or over the airconditioner must be operated with with water in the tank. 20 Setting the timer ELECTRICAL CONNECTION Before plugging in check that: · the mains supply corresponds to the power supply shown on the rating plate; · the socket and the mains lead correspond to the power requirements of the appliance; · the socket is suited to the plug, otherwise have the socket replaced; · the socket is properly grounded. The manufactures cannot be held responsible for any damages due to failure in following normal safety procedures. Replacement of the power cable must be carried out by qualified personnel. PROGRAMMED MODE 1) Set the operating times by pushing out the notches on the dial corresponding to the period required (each notch represents 15 mins. ) 2) Press the TIMER key 13 , the signal light 15 will come ON. 3) Make sure that the timer indicates the correct time (see instructions on setting). operating time Funzionamento 21 20 19 SETTING THE TIMER (if supplied) The programmer/timer 14 , like all clocks, must be set to the exact time. (16. 00), turn the dial in a clockwise direction (following the direction of the arrow) until the number 16 is lined up with the triangular pointer (the arrows indicates 4:00 P. M. approximately ). 4) Select the desired function as shown in the chart overleaf. N. B. : To override the programmed operating times, simply press the ON/OFF key 13 (the timer signal lamp ON will go out) 21 20 19 pointer N. B. : Never turn the dial in an anti-clockwise direction! The timer is in effect, an electric clock and works only if the plug is connected to the power supply. Whenever the plug is disconnected or there is a power failure, the programmer stops (the clock is then "slow") and must be re-set. 21 ITALIANO ITALIANO ITALIANO ITALIANO ITALIANO ITALIANO ITALIANO ENGLISH ITALIANO 16 16 Turning on and Selecting functions AIR CONDITIONING FUNCTIONS To turn the unit on in air conditioning mode, proceed as follows: 1. Press the button 12 (the signal light "I" 11 will come on). Delay on Start Up 1. A special safety device will delay the start of air conditionig by approximately 3 to 5 minutes when switching between functions or on initial start up. You may also experience a slight delay between changing from one function to another. 2. Rotate the function selector 16 dial anticlockwise: · Place the large star symbol in line with the reference mark to operate the unit in air conditioning mode at maximum fan speed. · Place the small star symbol in line with the reference mark to operate the unit in air conditioning mode at minimum fan speed. Now set the required temperature by rotating the room thermostat dial 17 . VENTILATION/FILTRATION Rotate the function selector 16 clockwise. · Press the button 12 (the signal light "I" 11 will come on). · Place the large symbol in line with the reference mark to operate the unit at maximum fan speed. · Place the small symbol in line with the reference mark to operate the unit at minimum fan speed. Note The temperature is not expressed in degrees. We recommend that you turn the thermostat dial to the maximum position. When the desired room temperature has been reached, slowly turn the thermostat 17 in a clockwise direction until it arrives at the position where a click can be heard. [. . . ] If it does not fit your socket, the plug should be cut off from the mains lead, and on appropriate plug fitted, as below. warning: Very carefully dispose of the cut off plug after removing the fuse: do not insert in a 13 Amp socket elsewhere in the house as this could cause a shock hazard. With alternative plugs not incorporating a fuse, the circuit must be protected by a 15 Amp fuse. If the plug is a mouldedon type, the fuse cover must be re-fitted when changing the fuse using a 13 Amp Asta approved fuse to BS 1362. [. . . ]