User manual DELONGHI PACN 125HP

[. . . ] Important safeguards · Use this appliance only as described in this instruction manual. As with all electrical equipment, whilst the instructions aim to cover as many eventualities as possible, caution and common sense should be applied when operating and installing this appliance. · This appliance is designed for home air conditioning and must not be used for other purposes. · It is dangerous to modify or alter the characteristics of the appliance in any way. [. . . ] Respect the height and dimensions of the hole given in figures M and I. NOTE: When installing the air conditioner semi-permanently, you should leave a door slightly open (as little as 1 cm) to guarantee correct ventilation. 6 Control panel THE CONTROL PANEL S Q O P N I T L M H G A B C R D E F DESCRIPTION OF THE CONTROL PANEL A ON/OFF button B MODE selection button Air conditioning, dehumidifying, fan, heating. C Fan speed selection button (MAX/MED/MIN) D Timer button E Programmed operation increase temperature/time button F Programmed operation decrease temperature/time button G Display Displays the temperature values set and the programmed operating time H Timer in operation indicator light I/L/M Fan speed lights N Fan/Heat mode light O Air-conditioning mode light P Dehumidifying mode light Q Alarm light R Remote control receiver S Light: the inner temperature is shown on the display T Light: the set temperature is shown on the display Never turn the air conditioner off by unplugging from the outlet. Always press the button, then wait for a few minutes before unplugging. This allows the appliance to perform a cycle of checks to verify operation. 7 Operation TURNING THE APPLIANCE ON Plug into an outlet. Two lines appear on the display indicating that the appliance is in stand-by. When turned on, the air conditioner starts operating in the same mode as when it was turned off. Press the MODE button (B) until the light corresponding to the desired mode lights up: Light (O): air-conditioning mode Light (P): dehumidifying mode Light (N): fan/heating mode (the light changes colour from yellow to red) AIR CONDITIONING MODE Ideal for hot muggy weather when you need to cool and dehumidify the room. The display shows the inner temperature: the light (S) turns on. To modify the set temperature, push the (E) or (F) button to reach the desired temperature. The (T) light turns on and the (S) light turns off. (To change from °F to °C or viceversa, press for few seconds both button E and F). After 15 seconds, the inner temperature is shown on the display. You can adjust the temperature only in air conditioning mode. Then select the fan speed by pressing the FAN button (C) until the light corresponding to the required fan speed lights up: MAX: the air conditioner operates at maximum to achieve the target temperature as rapidly as possible MED: reduces noise levels while maintaining a comfortable temperature MIN: for silent operation The most suitable temperature for the room during the summer varies from 75°F to 81°F (24 to 27°C). You are recommended, however, not to set a temperature much below the outdoor temperature FAN MODE Adjust fan speed by pressing the FAN button (C) as described for the air-conditioning mode. Remember that the higher the speed, the more air is filtered. If you select "MIN" speed, less air is filtered but the appliance is also less noisy. 8 Operation HEATING MODE This is ideal in spring and autumn when outdoor temperatures are not particularly severe. When using the appliance in this mode, the air hose must be be attached. To set this mode correctly: · Press the MODE button a number of times until the red light appears. · Select the target temperature by pressing the + or - button until the corresponding value is displayed. DEHUMIDIFYING MODE Ideal for reducing the humidity in a room without lowering or raising the temperature (spring or autumn, damp rooms, rainy spells, etc). When the dehumidifying mode is selected, the light (P) comes on. At the same time, the "MIN" fan speed light (M) comes on. [. . . ] To clean the filters, remove the filter as shown in figure N. Use a vacuum cleaner to remove the dust collected on the filter. If it is very dirty, immerse in warm water and rinse a number of times. The water should never be hotter than 40°C. [. . . ]