User manual DELONGHI PINGUINO PAC260

[. . . ] - Do not place any strain on the power cord. - Ensure that outlet vent of exhaust hose is kept free of debris and obstruction. - Ensure that ventilation holes on the rear of the machine and front louvers are not blocked. - The Pinguino should not be installed where the atmosphere could contain combustible gases. [. . . ] 1 cm is enough). 7 3"1/2 PAC260GB 24-04-2003 16:33 Pagina 8 Setting up TEMPORARY INSTALLATION Note: In both cases (permanent and temporary installations) make sure that the Pinguino is positioned on level ground. If necessary use the two caster stops for the front casters This installation makes it easy to use Pinguino in any room, provided there is a window or a door: it allows you to use the Pinguino immediately. window bracket fig. 5 Suction discs may be used to keep window or door closed. If you have a sash door, use the additional set provided in order to extend the accessory to the desired length; joining the two parts (fig. 8), adjust the total lenghth according to your needs then, fix the bracket with the relevant nuts, close the door and connect the hose (fig. 6 Pinguino is equipped with an adjustable window bracket. If you have a sash window, place the bracket on the window sill, extend the bracket fully within the window frame and lower the window onto the bracket. Insert the nozzle of the exhaust hose into the slot, then connect the hose to the air conditioner (fig. 7). Thanks to the wing nut, it's possible to use the window bracket also for sliding windows. Position the hole of the bracket so to allow a correct installation of the exhaust hose. fig. 9 8 PAC260GB 24-04-2003 16:33 Pagina 9 Setting up and recommendations SET UP INSTRUCTION For permanent installation place the Pinguino near the outlet opening in wall or window (where it is meant to be used). The diagram below shows the correct way to installl the exhaust hose. 1) Water collects at this point 2) Bend this section 3) Bend this section fig. 10 NO YES YES ELECTRICAL CONNECTION Check that the power supply voltage is 115 V ~ 60 Hz. Important: if you need to use and extension cord, please be sure to use a heavy duty extension cord (minimum 14 gauge). Before connecting the Pinguino to power supply, make sure that all switches on the front control panel are in the OFF position. Connect power cord found in storage compartment at rear of the Pinguino. fig. 11 FINAL CHECK In order to obtain the maximum performance from your air-conditioner make sure that: fig. 12 - Doors and windows of room to be air-conditioned are closed (with the exception of temporary installation where a partially opened window is necessary). 14 - Shade the room as far as possible from direct sunlight by drawing curtains and/or lowering blinds or shutters, for economical and efficient air-cooling. - Ensure that intake and outlet vents (fig. Make sure there are no sources of heat in the room. 9 PAC260GB 24-04-2003 16:33 Pagina 10 Control panel ON/OFF button ON/OFF pilot light "Alarm" pilot light Timer ON/OFF pilot light Timer notches Thermostat Timer ON/OFF button Selecting fan speed button SETTING THE TIMER The programmer/timer, like all clocks, must be set to the exact time. If for example it is 4. 00 p. m. , turn the dial in a clockwise direction (following the direction of the arrow) until the number 4 is lined up with the arrow pointer (the arrows indicates 4:00 p. m. approximately). 1) Release B timer button 2) Set the operating times by pushing out the notches on the dial corresponding to the period required (each notch represents 15 mins. ). 3) Check that the timer indicates the correct time (see instructions on setting). Operating time eg. [. . . ] 20 Remove dust with a vacuum cleaner Rinse with running water fig. 21 Cleaning procedure To remove dust deposited on filter, use a vacuum cleaner. If it is very dirty, soak in lukewarm water and rinse thouroghly. The temperature of the water must be kept below 104°F. [. . . ]