User manual DELONGHI XCA 245.1

[. . . ] They are only different in appearance - the operating instructions are the same. 10 GB 16-04-2004 9:28 Pagina 11 ENGLISH IMPORTANT SAFEGUARDS 1) Read the instruction booklet carefully 2) Never use the appliance on wet surfaces. 3) Always unplug the appliance when not in use and before carrying out any maintenance or cleaning work on the appliance itself. 4) The appliance is only intended for domestic use, as shown in the booklet, and only with the accessories supplied. 5) Do not leave the appliance unattended when switched on. [. . . ] 23) For all repairs, apply only to the place of purchase or directly to an authorized Technical Service Centre. KEEP THESE INSTRUCTIONS The manufacturer reserves the right to modify the appliance and/or accessories supplied without prior notice. 11 GB 16-04-2004 9:28 Pagina 12 ASSEMBLING THE APPLIANCE Attach the handle (1) by pushing in firmly. Insert the screw with screw plug in (fig. 1, A) the through hole and then insert the cord-winding lug and the clamping screw (fig. 2) and screw in. 3 - Attach the desired tool to the end of the vacuum cleaner, pushing it in well. "Explora" brush (some models only) Thanks to the articulated fins, this model is particularly suited to cleaning right up close to furniture and into corners. 1A 1 4 For cleaning wider areas, simply rotate the brush to use the total width (Fig. 5). 2 - Open the front panel of the appliance (7) by pushing the release catch in a downwards direction (fig. 3) and check that the paper bag is properly inserted in its holder. 5 12 GB 16-04-2004 9:28 Pagina 13 Accessory for delicate floors of the "Explora" brush (some models only) The accessory features felt strips for using the brush on delicate surfaces such as parquetry and treated marble. To fit the accessory to the base of the "EXPLORA" brush, line up the two pins on the accessory with the two holes on the bottom of the brush and press until it 6 clicks into place. USING THE APPLIANCE Electronic version (if provided) The appliance is equipped with a knob which allows an electronic control of the suction power (fig. 8). Carpet/floor brush (some models only) The carpet/floor nozzle has a two position foot-operated lever (fig. 7). 8 It is advisable to set the knob to minimum before turning on the appliance. - Maximum power: recommended for heavy dirt (small stones, soil etc. ) on hard floors, fabric covered floors, deep pile carpets, corners, edges etc. - Medium power: saves energy and reduces the noise level of the appliance. This is quite sufficient for removing dust from hard floors and fabric furnishings. - Minimum power: perfect for vacuuming light, delicate objects and light fabric coverings as it prevents the material being sucked into the appliance making it difficult to clean. Plug in the power cord and turn on the appliance with the switch on the handle (2) (fig. 9). 7 - when the lever is set to `hard floors' ( ), the brushes are extended for cleaning hard flooring surfaces (marble, linoleum, bathroom floors etc. ). - when the lever is set to `carpets' ( ), the brushes are withdrawn for cleaning textiles (carpet, rugs etc. ). Parquet brush (15) (some models only): The parquet brush has soft natural horsehair bristles and felt wheels which run over even the most delicate floor without damaging it. 9 13 GB 16-04-2004 9:28 Pagina 14 Models with three-position switch In this version, the switch has two positions: ECON and SUPERPOWER. With the switch in the ECON (economy mode) position, the cleaner functions at two thirds of maximum power. In this position, the regulator knob can be used to vary suction force from minimum to the maximum possible in economy mode. With the switch in the SUPER POWER position, the appliance uses the maximum power available. [. . . ] If it does not fit your socket, the plug should be cut off from the mains lead, and an appropriate plug fitted, as below. WARNING: Very carefully dispose of the cut off plug after removing the fuse: do not insert in a 13 Amp socket elsewhere in the house as this could cause a shock hazard. With alternative plugs not incorporating a fuse, the circuit must be protected by a 15 Amp fuse. If the plug is a moulded-on type, the fuse cover must be re-fitted when changing the fuse using a 13 Amp Asta approved fuse to BS 1362. [. . . ]