User manual DELPHI ROADY SA10069 Install Guide

[. . . ] Delphi will not be responsible for damage resulting from any (i) deviation from Delphi's operating instructions as printed in Delphi's catalog or on any packaging, labels, or other literature provided with a Product, (ii) installation of a Product in a manner which is inconsistent with Delphi's written instructions, (iii) alteration or modification of a Product, (iv) misuse, (v) neglect, (vi) abuse, (vii) accident, (viii) normal wear and tear, (ix) commercial use, (x) improper storage, (xi) environmental conditions, including excessive temperature or humidity, (xii) service by anyone other than a Delphi authorized repair facility, (xiii) other improper application, installation or operation of the Product, or (xiv) defects or malfunctions of which Delphi is not advised within ten (10) days of the expiration of the limited warranty period. How you (the Customer) can get service: To obtain warranty service, you must return the defective Product with the original receipt to the original place of purchase. If further clarification or additional information is required from Delphi, you may call Delphi at: 1. 877. GO DELPHI (1. 877. 463. 3574). If warranty service is needed at any time during the warranty period, the purchaser will be required to furnish a sales receipt/proof of purchase indicating the date of purchase, amount paid, and place of purchase. [. . . ] Customer Service: [1] 877. GO DELPHI The Roady name, Roady2 name, XM name, and related logos are trademarks of XM Satellite Radio Inc. Printed on Recycled Paper ©2004 Delphi Corporation. DPSS-04-E-043 www. delphi. com Warning: This guide and the user guide that came with your Roady or Roady2 contain important safety and operating information. Please read and follow the instructions in these manuals. Failure to do so could result in personal injury or damage to your unit or property. 6V A/C power adaptor Remote control Audio cable Figure 1. Connect components to your unit as shown. 8816DM Roady Card Keys 6/25/04 8:06 AM Page 2 Roady Home Stand Installation 1. Insert the unit into the Roady Home Stand and press the power button. If the display reads "ANTENNA, " check that the antenna connection is secure and completely pushed in. Next, change channels (from 0 to 1 or from 1 to 0 if the receiver is not authorized yet). If the "ANTENNA" message remains, power down the radio, unplug the antenna, and look for any obvious damage. If no damage is detected, reconnect the antenna, turn the unit back on, and change channels again. If the message still appears, contact your retailer. If the display reads "NO SIGNAL, " your antenna needs to be repositioned. See the next section for more information. XM Home Antenna Set-up The position of your antenna must be optimized to receive the strongest possible signal and consistent, mute-free reception. Your unit has a basic signal-strength indicator visible at the top of the display screen during normal listening. It has from zero to three vertical bars; three bars represent the strongest signal. The supplied antenna is a high-gain antenna that can receive XM's signal from one of XM's satellites and/or, depending on where you live, XM's terrestrial repeaters. For best results, the antenna should be positioned near a south-facing window or outdoors with a clear view of the southeastern sky. In some cases, it will be possible to receive XM's signal through standard home walls or a roof. You can install your antenna either indoors or outdoors, following these steps: Indoor installation on a flat surface 1. Set the antenna flat against its base on a flat (horizontal) surface. [. . . ] Use an XM-approved extension kit (Delphi model number SA10006) with your unit. Failure to do so could damage the unit. 1. 6 in. Tilt the antenna fully back on the base, place the antenna base on the four screw heads with the antenna pivot on tip, and pull down approximately 1/4 inch until the base is firmly secured. Note that the XM logo will be upside down when the antenna is properly installed. [. . . ]