User manual DELTA DORE RF 660 WIRELESS RECEIVER GUIDE D INSTALLATION

[. . . ] · Do not attempt to repair the unit yourself; an after-sales service is available. · The diagrams provided are simplified for greater clarity. The protective devices and other accessories required by the standards are not illustrated. [. . . ] - Connect the receiver then fit back the convector. Important: the operating temperature of the receiver must not exceed 50°C. You must not install the receiver to near the hottest parts of the convector. 1 2 N L Pilot wire Blue Brown Black http://pro. deltadore. com DELTA DORE TALCO - Bonnemain - F-35270 COMBOURG - FRANCE E-mail: deltadore@deltadore. com 3 4 blue wire brown wire black wire N L Position behind the convector You must let the radio antenna project from the top of the convector to obtain a correct radio transmission. Antenna radio Convector No Screw-mounting Mounted on a wall using the screws and pegs supplied. Device complying with the requirements of the directives: R&TTE 1999/5/CE Because of changes in standards and equipment, the characteristics given in the text and the illustrations in this document are not binding unless confirmed by Delta Dore. Mounting by double-sided adhesive tape Secure to the wall by using the double-sided adhesive tape supplied. Ensure that the surface on which the tape is applied is thoroughly clean before attaching the tape. Association Associating the receiver with a transmitter On the receiver: Press the button for about 3 seconds until the two LEDs flash: the receiver is in association mode. On the transmitter: Depending on the transmitter, go to radio configuration mode. On the receiver: The two LEDs stop flashing to confirm the association operation. Home automation functions The product is compatible with the following X2D transmitters: - door/window magnetic contacts (heating goes to frost protection mode when a window is opened), - telephone transmitters (remote control of the heating), - on/off, raise/lower and scenario home automation remote controls (in automatic mode: the product sets up a local override in Comfort or in Economy mode), - wireless alarm control units (in automatic mode: switch to economy mode when the alarm is activated and return to comfort mode when the alarm is deactivated). To associate the transmitters, refer to the "Association" section. Operation The LEDs show you the current mode: or . Removing all the receiver associations Press and hold the button. The LEDs are deactivated after 10 seconds. The LED flashes after 30 seconds; all the associations are removed. Release the button. The médio (Comfort -1°C) and modérato (Comfort -2°C) modes are displayed by the The LEDS are off for the Frost Protection and Off modes. The heat emitter must be in the automatic setting for the programmer to be able to control it. Override You can locally interrupt the current mode up to the next change of order sent by the control unit. Pressing the button carries out the override. The change is shown as follows: - the LED flashes during an override of the Comfort mode to the Eco mode, - the LED flashes during an override of the Eco mode to the Comfort mode. Note: the association remains in the event of a power failure. Important: an override is cancelled if there is a power failure. Turning off the LEDs You can keep the LEDs turned off permanently so that they do not annoy you during the night: - press and hold the receiver button for about 10 seconds, - all the LEDs switch off while letting the product function normally. To turn on the LEDs: - press and hold the receiver button for about 10 seconds, - the LEDs switch on according to the current operating mode. Technical characteristics · · · · · · 230 V, 50 Hz power supply, +/-10% Class II insulation Power consumption: 0. 5 VA Pilot wire output 0. 1 A, 230 V, Radio frequency 868 MHz (standard EN 300 220) Radio range 100 to 300 metres outside, variable depending on the associated equipment (the range can be altered depending on the installation conditions and the electromagnetic environment) Number of transmitters that may be associated with the receiver: 8 max. Operating temperature: -5°C to +50°C Storage temperature: -10 to +70°C Dimensions: 102 x 54 x 20 mm, Protection index: IP44 - IK 04 Install in an environment with normal pollution levels Troubleshooting You cannot associate a transmitter with your receiver. The maximum number of transmitters to associate with a receiver function is 8. [. . . ] · The power of the convector is insufficient. Replace the convector with a more powerful model. · You have subscribed to the tempo tariff and you are in an economy period. [. . . ]