User manual DENON AVR-2105

[. . . ] AV SURROUND RECEIVER RÉCEPTEUR AUDIO-VIDÉO AVR-2105/885 OPERATING INSTRUCTIONS MODE D'EMPLOI MASTER VOLUME FUNCTION VOLUME LEVEL SIGNAL DIGITAL AUTO INPUT PCM DTS OUTPUT SURROUND ZONE 2 BACK INPUT MODE ANALOG EXT. IN BAND SHIFT ª PRESET · ª TUNING · VIDEO SELECT DIMMER STATUS MAIN SOURCE ZONE 2 / REC SELECT ON / STANDBY ON OFF PHONES A SPEAKER B SURROUND BACK STANDARD 5CH / 7CH STEREO DIRECT / STEREO SURROUND MODE V. AUX INPUT SELECT TONE CONTROL SURROUND PARAMETER S-VIDEO VIDEO L AUDIO R OPTICAL SETUP MIC TONE DEFEAT AV SURROUND RECEIVER AVR-2105 FOR ENGLISH READERS PAGE 2 ~ PAGE 73, 144 ~ 148 POUR LES LECTEURS FRANCAIS PAGE 2, 74 ~ PAGE 148 2 We greatly appreciate your purchase of this unit. 2 To be sure you take maximum advantage of all the 2 Nous vous remercions pour l'achat de cet appareil. 2 Pour être sûr de profiter au maximum de toutes les features this unit has to offer, read these instructions carefully and use the set properly. [. . . ] This mode can be selected for all input sources other than PHONO and TUNER. The presence or absence of digital signals is detected, the signals input to the digital input jacks are identified and decoding and playback are performed automatically in DTS, Dolby Digital or PCM (2 channel stereo) format. If no digital signal is being input, the analog input jacks are selected. Use this mode to play Dolby Digital signals. w PCM (exclusive PCM signal playback mode) Decoding and playback are only performed when PCM signals are being input. Note that noise may be generated when using this mode to play signals other than PCM signals. e DTS (exclusive DTS signal playback mode) Decoding and playback are only performed when DTS signals are being input. r ANALOG (exclusive analog audio signal playback mode) The signals input to the analog input jacks are decoded and played. IN (external decoder input jack selection mode) The signals being input to the external decoder input jacks are played without passing through the surround circuitry. NOTE: · Note that noise will be output when CDs or LDs recorded in DTS format are played in the "PCM" (exclusive PCM signal playback) or "ANALOG" (exclusive PCM signal playback) mode. Select the AUTO or DTS mode when playing signals recorded in DTS. To select the input source when ZONE2/REC OUT is selected, press the MAIN button then operate the input function selector. MAIN (Main unit) 2 Select the input mode. · Selecting the analog mode Press the ANALOG button to switch to the analog input. ANALOG (Main unit) (Remote control unit) · Selecting the external input (EXT. IN (Main unit) (Remote control unit) · Selecting the AUTO, PCM and DTS modes The mode switches as shown below each time the INPUT MODE button is pressed. AUTO PCM DTS INPUT MODE (Main unit) (Remote control unit) Notes on playing a source encoded with DTS · Noise may be generated at the beginning of playback and while searching during DTS playback in the AUTO mode. · In some rare cases the noise may be generated when you preform the operation to stop playback of a DTS-CD or DTS-LD. 40 ENGLISH Input mode display · In the AUTO mode AUTO INPUT PCM DTS 3 Select the play mode. Press the SURROUND MODE button, then turn the SELECT knob. Example: Stereo One of these lights, depending on the input signal. DIGITAL ANALOG · In the DIGITAL PCM mode SURROUND MODE SELECT AUTO INPUT PCM DTS DIGITAL · In the DIGITAL DTS mode (Main unit) (Remote control unit) SURROUND MODE AUTO INPUT PCM DTS DIGITAL To select the surround mode while adjusting the surround parameters, tone defeat or tone control, press the surround mode button then operate the selector. · In the ANALOG mode AUTO INPUT PCM DTS ANALOG (Main unit) Input signal display · DOLBY DIGITAL SIGNAL DIGITAL 4 5 Start playback on the selected component. · For operating instructions, refer to the component's manual. Adjust the volume. MASTER VOLUME · DTS SIGNAL DIGITAL · PCM The volume level is displayed on the master volume level display. SIGNAL DIGITAL (Main unit) (Remote control unit) The volume can be adjusted within the range of ­70 to 0 to 18 dB, in steps of 0. 5 dB. However, when the channel level is set as described on page 48, if the volume for any channel is set at +0. 5 dB or greater, the volume cannot be adjusted up to 18 dB. (In this case the maximum volume is adjusted to "18 dB -- (Maximum value of channel level)". ) Input mode when playing DTS sources · Noise will be output if DTS-compatible CDs or LDs are played in the "ANALOG" or "PCM" mode. When playing DTS-compatible sources, be sure to connect the source component to the digital input jacks (OPTICAL/COAXIAL) and set the input mode to "DTS". The DIGITAL indicator lights when digital signals are being input properly. [. . . ] · The unit is operating at continuous high power conditions and/or inadequate ventilation. 5, 14 Sound produced only from one channel. · Incomplete connection of speaker cords. · Incomplete connection of input/output cords. · Reverse connections of left and right speakers or left and right input/output cords. · Ground wire of turntable not connected properly. [. . . ]