User manual DENON AVR-3803

[. . . ] AV SURROUND RECEIVER AVR-3803/1083 OPERATING INSTRUCTIONS AMP REMOTE SENSOR SIGNAL DIGITAL SURROUND BACK CH OUTPUT VOLUME LEVEL ON / STANDBY AUTO INPUT PCM DTS SIGNAL DETECT 2 We greatly appreciate your purchase of the AVR-3803/1083. 2 To be sure you take maximum advantage of all the features the AVR-3803/1083 has to offer, read these instructions carefully and use the set properly. Be sure to keep this manual for future reference, should any questions or problems arise. "SERIAL NO. PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE CABINET FOR FUTURE REFERENCE" 2 SAFETY PRECAUTIONS CAUTION TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. ATTENTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTERODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] · "SEL" appears on the remote control unit's display. 4 Use the · and ª cursor buttons to display the mode you want to punch through, then press the ENTER button. · "OK" is displayed and the punch through is set. The display switches as shown below each time the · and ª cursor buttons are pressed. AMP DBS CABLE TV The display switches as shown below each time the · and ª cursor buttons are pressed. CD CDR VCR2 MD VCR1 TAPE VDP DVD It is also possible to select the mode directly using the mode buttons. It is also possible to select the mode directly using the mode buttons. 41 Setting the back light's lighting time 1 Press the power ON/SOURCE button and the OFF button at the same time. · "PRE" appears on the remote control unit's display. 1 DVD 1 2 Use the · and ª cursor buttons to display "BKLT" on the remote control unit, then press the ENTER button. · "05SEC" appears on the remote control unit's display. 2, 3 3 Use the · and ª cursor buttons to adjust the lighting time (3 sec ~ 30 sec), then press the ENTER button. · "OK" is displayed and that lighting time is set. 2, 3 Resetting (1) Resetting the preset memory 1 Press the power ON/SOURCE button and the OFF button at the same time. · "PRE" appears on the remote control unit's display. 1 DVD 1 2 Use the · and ª cursor buttons to display "RST" on the remote control unit, then press the ENTER button. 2, 3, 4 2, 3, 5 42 3 Use the · and ª cursor buttons to display "PRE" on the remote control unit, then press the ENTER button. · After "SEL" is displayed on the remote control unit's display, the registered preset memory is displayed on the remote control unit's display. 5 When the mode you want to reset is shown on the remote control unit's display, press the ENTER button to reset the preset memory. · The LCD's back light flashes during the resetting operation, and when the operation is completed, "OK" is displayed and the set returns to the normal operating mode. 4 Use the · and ª cursor buttons to select the code to be reset. (2) Resetting "learned" buttons 1 Press the power ON/SOURCE button and the OFF button at the same time. · "PRE" appears on the remote control unit's display. 1 DVD 1 2 Use the · and ª cursor buttons to display "RST" on the remote control unit's display, then press the ENTER button. · "PRE" is displayed. 2, 3, 4 3 Use the · and ª cursor buttons to display "LRN" on the remote control unit's display, then press the ENTER button. · "SEL" is displayed. 2, 3, 4 4 Use the · and ª cursor buttons to select the mode of the button to be reset, then press the ENTER button. · The LCD's back light flashes during the resetting operation, and when the operation is completed, "OK" is displayed and the set returns to the normal operating mode. 43 (3) Resetting the system call buttons 1 Press the power ON/SOURCE button and the OFF button at the same time. · "PRE" appears on the remote control unit's display. 1 DVD 1 2 Use the · and ª cursor buttons to display "RST" on the remote control unit, then press the ENTER button. · "PRE" appears on the remote control unit's display. 2, 3, 4 3 Use the · and ª cursor buttons to display "CALL" on the remote control unit, then press the ENTER button. · "SEL" appears on the remote control unit's display. 2, 3, 5 4 Press the · and ª cursor buttons to select the system call setting to be reset. The remote control unit's display switches as shown below each time the · and ª cursor buttons are pressed. SYS CALL 1 SYS CALL 2 5 To reset CALL 1 or CALL 2, select "CALL 1" or CALL 2", then press the ENTER button. · The LCD's back light flashes during the resetting operation, and when the operation is completed, "OK" is displayed and the set returns to the normal operating mode. 44 (4) Resetting the punch through setting 1 Press the power ON/SOURCE button and the OFF button at the same time. · "PRE" appears on the remote control unit's display. 1 DVD 1 2 Use the · and ª cursor buttons to display "RST" on the remote control unit, then press the ENTER button. 3 Use the · and ª cursor buttons to display "PUNCH" on the remote control unit, then press the ENTER button. · "SEL" appears on the remote control unit's display. 2, 3, 4 2, 3, 4 4 Use the · and ª cursor buttons to display the mode whose punch through setting you want to cancel, then press the ENTER button. · The LCD's back light flashes during the resetting operation, and when the operation is completed, "OK" is displayed and the set returns to the normal operating mode. The display switches as shown below each time the · and ª cursor buttons are pressed. [. . . ] Large DOLBY/ DTS SURROUND Center Sp. Small WDE SCREEN Sub Woofer Yes 5CH/7CH STEREO Surround Sp. A/B Small DSP SIMULATION Surround Back Sp. IN q Surround Speaker Setting Surround speaker A A A A A Crossover Frequency Subwoofer mode Set the frequency (Hz) below which the bass sound of the various speakers is to be output from the subwoofer. [. . . ]