User manual DENON AVR-3805

[. . . ] AV SURROUND RECEIVER AVR-3805 OPERATING INSTRUCTIONS CH SEL ENTER 2 We greatly appreciate your purchase of the AVR-3805. 2 To be sure you take maximum advantage of all the features the AVR-3805 has to offer, read these instructions carefully and use the set properly. Be sure to keep this manual for future reference, should any questions or problems arise. "SERIAL NO. PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE CABINET FOR FUTURE REFERENCE" 2 SAFETY PRECAUTIONS CAUTION TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. ATTENTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTERODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] For some models the remote control unit or the device may not operate properly. In this case, use the learning function (page 56) to store your device's remote control signals in the included remote control unit. For instructions on resetting the preset memory, see page 60. 1 Press the power ON button and the OFF button at the same time. 1 5 3 2 Press the "1"button to select preset memory. · Setup List 1: 2: 3: 4: 5: 6: Preset memory Learning setup System call Punch through Light setup Reset 2, 4 3 Press the Mode button for the component you want to preset, then press ENTER button. CH SEL ENTER 3 4 Referring to the included List of Preset Codes, use the number buttons to input the preset code (a 4-digit number) for the manufacturer of the component whose signals you want to store in the memory. 5 6 "OK" is displayed when the signals are registered and the mode is terminated. "FAIL" is displayed when the signals are not registered, repeat steps 1 to 5. To store the codes of another component in the memory, repeat steps 1 to 5. NOTES: · Depending on the model and year of manufacture, this function cannot be used for some models, even if the your device is listed on the included list of preset codes. · Some manufacturers use more than one type of remote control code. Refer to the included list of preset codes to change the number and check it out. The preset codes are as follows upon shipment from the factory and after resetting: TV, VCR1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HITACHI CD, MD, TAPE, CDR, VDP, DVD, DVDR. . . . . . . . . . . . . . . . . . . . . . DENON VCR2, DBS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SONY CABLE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ABC 53 Operating a component stored in the preset memory 1 Press the mode selector button for the component you want to operate. 1 NOTE: · For the DVD player remote control buttons, function names may differ according to manufacturer. Compare with the remote control operation of the various components. 2. Video disc player (VDP) system buttons 2 Operate the component. · For details, refer to the component's operating instructions. Some models cannot be operated with this remote control unit. 1. Digital video disc player (DVD), Digital video disc recorder (DVD R) system buttons SOURCE ON : Power on SOURCE OFF : Power off (DENON DVD only) 6, 7 : Manual search (forward and reverse) 2 : Stop 1 : Play 8, 9 : Auto search (to beginning of track) 3 : Pause DISC SKIP + : Disk skip (for DVD changers only) SETUP : Setup TOP MENU : Top menu MENU : Menu RETURN : Return ·, ª, 0, 1 : Cursor up, down, left and right ENTER : Enter AUDIO : Switch the audio language DISPLAY : Display SUBTITLE : Switch the subtitle ANGLE : Switch the angle 0~9, +10 : 10 key SOURCE ON : 6, 7 : 2 : 1 : 8, 9 : 3 : 0~9, +10 : Power on/Standby Manual search (forward and reverse) Stop Play Auto search (cue) Pause 10 key 54 3. Video deck (VCR-1/VCR-2) system buttons 4. Monitor TV (TV), digital broadcast satellite (DBS) tuner and cable (CABLE) system buttons SOURCE ON : 6, 7 : 2 : 1 : 3 : 0~9, +10 : Power on/Standby Manual search (forward and reverse) Stop Play Pause 10 key SOURCE ON : 6, 7 : SETUP : TOP MENU : MENU : RETURN : ·, ª, 0, 1 : ENTER : DISPLAY : Channel +, ­ : 0~9, +10 : TV/VCR : VOL +, ­ : Power on/standby Manual search (forward and reverse) Setup Top menu Menu Return Cursor up, down, left and right Enter Switch display Switch channels +, ­ 10 key Switch between TV and video player Volume up/down 55 Learning function If your AV component is not a Denon product or if it cannot be operated using the preset memory, it can be controlled with the accessorious remote control unit by storing its remote control signals in the remote control unit. For some remote control signals it is not possible to "learn" the signals or the device will not operate properly. In such cases use the remote control unit included with the device to operate it. 1 2 Press the power ON button and the OFF button simultaneously. 1, 8 Press the "2" button to select Learning setup. 3, 7 2 3 Press the Mode button for the component you want to learned, then press the ENTER button. Learning is not possible for the AMP, ZONE2, and ZONE3 modes. CH SEL ENTER 3 4 Buttons that allow learning will light. Press the button that you wish to be learned. The display will go off and the unit will enter the learning standby mode. · To cancel, press the power ON button and the OFF button simultaneously. 6 7 5 Point the remote control units directly at each other and press and hold in the button on the other remote control unit which you want to "learn". Other remote control unit "OK" appears on the remote control unit's display and learning is completed. [. . . ] Large Front L & R 12 ft (3. 6 m) Front L 0 dB Front R 0 dB Center Sp. Small Center 12 ft (3. 6 m) Center 0 dB Subwoofer Yes Subwoofer 12 ft (3. 6 m) Surround L Surround R 1 Surround Sp. A/B Small Surround L & R 10 ft (3. 0 m) Surround Back L Surround Back Sp. Small / 2spkrs SBL & SBR 10 ft (3. 0 m) Surround Back R 2 Delay Time 3 4 5 Channel Level Crossover Frequency Subwoofer mode Subwoofer 0 dB 0 dB 80Hz LFE WIDE SCREEN 0 dB 0 dB 0 dB 6 (Surround Speaker Setting) 5CH/7CH STEREO DSP SIMULATION MULTI CH MODE EXT. IN Surround speaker A A A A A A A A 2. Input Setup Input Setup Digital In Assignment Ext. [. . . ]