User manual DENON AVR-4800

[. . . ] AV SURROUND RECEIVER AVR-4800 OPERATING INSTRUCTIONS START SYSTEM CALL LEARNED/TX POWER RC-869 ON / SOURCE SHIFT SET DVD CALL VDP OFF TUNER 1 TV/DBS 2 V. AUX 3 PHONO 4 VCR-1 5 CD 6 MD / TAPE-1 CHANNEL 7 VCR-2 8 0 9 TAPE-2 MON TV/VCR MASTER VOLUME INPUT SELECTOR VOLUME LEVEL REMOTE SENSOR CH INDICATOR C R +10 A/B VOLUME DISC SKIP+ L LOCK HOME THX CINEMA DOLBY / DTS SURROUND DIRECT SL S SR LFE SURROUND BACK DSP SIMULATION 5CH/7CH STEREO STEREO MASTER VOL. ON / STANDBY INPUT MODE ANALOG EXT. IN HOME THX CINEMA TAPE-2 MON SURROUND SPEAKER A B AUDIO PHONO CD TUNER DVD VDP TV / DBS VCR-1 VCR-2 V. AUX MD / TAPE-1 TAPE-2 MON CD VIDEO DECK MD MULTI TV MUTING AVR/AVC DVD VDP VCR SYSTEM SETUP TUNING SURROUND PARAMETER TITLE BAND CH SELECT MENU/GUIDE MODE ENTER SELECT PHONES 6. 1 / 7. 1 SURROUND DIRECT STEREO DOLBY / DTS SURROUND SURROUND MODE 5CH / 7CH DSP STEREO SIMULATION TUNING PRESET SHIFT DOWN UP BASS TREBLE MEMORY PANEL DISPLAY ON SCREEN RETURN INPUT MODE ANALOG 6CH / 8CH EXT. IN VIDEO SELECT TONE DEFEAT USE/LEARN T. TONE MULTI SET UP STATUS DIMMER MODE SOURCE INPUT REC / MULTI PRECISION AUDIO COMPONENT / AV SURROUND RECEIVER AVR-4800 2 We greatly appreciate your purchase of the AVR-4800. 2 To be sure you take maximum advantage of all the features the AVR-4800 has to offer, read these instructions carefully and use the set properly. [. . . ] · If a non-learnable button is pressed or two or more buttons are pressed at once, the two LEDs will once again light when the button(s) is released. · If the codes could not be stored, the LEARNED/TX LED does not light after the START LED turns off. For limited number of models, codes cannot be stored in RC-869. · If the two LEDs start flashing rapidly after the START LED lights, this means that the memory is already full, and the code you have just attempted to store was not stored. To "learn" that code, first perform the resetting operation. (See page 39. ) 36 System call function · The included remote control unit is equipped with a system call function for transmitting multiple remote control signals when a single button is pressed (this is often referred to as a "macro" function). This function can be used to turn on the amplifier's power, select the input source, turn on the monitor TV's power, turn on a source component's power and start playback, etc. , all at the touch of a button. (1) System call buttons The buttons that can be used for the system call function are shown on the table below. A series of up to 10 operations can be performed with the POWER ON and OFF buttons, and a series of up to 5 operations can be performed with other buttons. System call signals are already preset at the buttons indicated in the shaded section. System call signals can also be stored at any button on the remote control unit, including the buttons in this section. (See page 38. ) Button POWER OFF (key 3) POWER ON (key 4) No. transmissions 10 10 DVD player (DVD) power on LD player (VDP) power on Receiver input source switched to DVD Receiver input source switched to VDP Receiver input source switched to TV/DBS Receiver input source switched to V. AUX Receiver input source switched to VCR-1 Video (VCR) playback DVD player (DVD) playback LD player (VDP) playback Stored operation 1 Stored operation 2 Stored operation 3 Stored operation 4 Stored operation 5 Stored operation 6 Stored operation 7 Stored operation 8 Stored operation 9 Stored operation 10 DVD (key 5) 5 Receiver power on TV power on VDP (key 6) 5 Receiver power on TV power on TV/DBS (key 9) 5 Receiver power on TV power on V. AUX (key 10) 5 Receiver power on The system call signals for the POWER OFF and POWER ON buttons are transmitted from the remote control unit approximately once every second. The signals for the other buttons (DVD, VDP, TV/DBS, V. AUX, VCR-1 and CD) are transmitted approximately once every 1. 5 seconds. TV power on VCR-1 (key 13) 5 Receiver power on Video (VCR) power on Receiver input source switched to CD TV power on CD (key 14) 5 Receiver power on (2) Using the system call function 1 2 Press the system call button. · The LEARNED/TX LED flashes for 5 seconds. CALL 1 START SYSTEM CALL LEARNED/TX POWER RC-869 ON / SOURCE SHIFT SET DVD CALL VDP OFF TUNER 1 2 V. AUX 3 PHONO 2 Press the button at which the desired system call signals are stored while the LEARNED/TX LED is flashing. · The preset signals or the signals you have stored at that button are transmitted in succession. TV/DBS 4 VCR-1 5 CD 6 MD / TAPE-1 CHANNEL 7 VCR-2 8 0 9 TAPE-2 MON TV/VCR +10 A/B VOLUME DISC SKIP+ HOME THX CINEMA DOLBY / DTS SURROUND DIRECT DSP SIMULATION 5CH / 7CH STEREO STEREO MASTER VOL. INPUT MODE ANALOG EXT. IN AUDIO AVR/AVC VIDEO DECK MD CD MULTI DVD VDP VCR TUNING SYSTEM SETUP MUTING TV SURROUND PARAMETER TITLE BAND CH SELECT MENU/GUIDE MODE ENTER SELECT 37 (3) Storing signals (4) Clearing system call settings 1, 5 2 START SYSTEM CALL LEARNED/TX POWER RC-869 ON / SOURCE SHIFT SET DVD CALL VDP OFF TUNER 1, 3 2 START SYSTEM CALL LEARNED/TX POWER RC-869 ON / SOURCE SHIFT SET DVD CALL VDP OFF TUNER 1 TV/DBS 2 V. AUX 3 PHONO 1 TV/DBS 2 V. AUX 3 PHONO 4 VCR-1 5 CD 6 MD / TAPE-1 CHANNEL 4 VCR-1 5 CD 6 MD / TAPE-1 CHANNEL 7 VCR-2 8 0 9 TAPE-2 MON TV/VCR 7 VCR-2 8 0 9 TAPE-2 MON TV/VCR +10 A/B +10 A/B VOLUME DISC SKIP+ VOLUME DISC SKIP+ HOME THX CINEMA DOLBY / DTS SURROUND DIRECT HOME THX CINEMA DOLBY / DTS SURROUND DIRECT DSP SIMULATION 5CH / 7CH STEREO STEREO MASTER VOL. DSP SIMULATION 5CH / 7CH STEREO STEREO MASTER VOL. INPUT MODE ANALOG EXT. IN INPUT MODE ANALOG EXT. IN 3 AUDIO AVR/AVC VIDEO CD DECK MD MULTI TV VDP VCR MUTING AUDIO AVR/AVC VIDEO CD DECK MD MULTI TV MUTING DVD SYSTEM SETUP DVD VDP VCR SYSTEM SETUP TUNING SURROUND PARAMETER TUNING SURROUND PARAMETER TITLE BAND CH SELECT MENU/GUIDE BAND TITLE CH SELECT MENU/GUIDE MODE ENTER SELECT MODE ENTER SELECT MEMORY STATUS DISPLAY ON SCREEN MEMORY STATUS DISPLAY ON SCREEN RETURN RETURN USE/LEARN T. TONE MULTI SPEAKER DVD SET UP USE/LEARN T. TONE MULTI SPEAKER DVD SET UP 1 2 3 Press the SET button. · The START LED and LEARNED/TX LED both flash. SET 1 2 3 Press the SET button. SET Press the button whose settings you want to clear. Press the button at which you want to store the system call signals. Set the mode switch to the position for the component whose remote control signals you want to store. AUDIO AVR/AVC VIDEO CD DECK MD MULTI TV VDP VCR Press the SET button. · The button is reset to the settings shown on the table on page 37. SET DVD 4 5 Press the buttons whose remote control signals you want to store one by one. Press the SET button. SET NOTES: · The remote control signals for the buttons pressed while storing the system call signals are transmitted when the buttons are pressed, so cover the remote sensor or take other measures so that the components do not operate while the signals are being stored. · The LEARNED/TX LED does not light if system call signals cannot be stored at the button that you have pressed or if you have already stored the maximum number of signals. 38 Clearing "learned" remote control signals 1 Press the USE/LEARN selector button with the tip of a pen, etc. , to set the learn mode. 4 START SYSTEM CALL LEARNED/TX POWER SET DVD CALL VDP OFF TUNER ON / SOURCE SHIFT 1 TV/DBS 2 V. AUX 3 PHONO 4 VCR-1 5 CD 6 MD / TAPE-1 CHANNEL 7 VCR-2 8 0 9 TAPE-2 MON TV/VCR +10 A/B VOLUME DISC SKIP+ HOME THX CINEMA DOLBY / DTS SURROUND DIRECT DSP SIMULATION 5CH / 7CH STEREO STEREO MASTER VOL. INPUT MODE ANALOG EXT. IN 2 3 To clear "learned" remote control signals, set the slide switch to the position at which the signals were "learned". AUDIO 2 AUDIO AVR/AVC VIDEO CD DECK MD MULTI TV MUTING DVD VDP VCR SYSTEM SETUP TUNING SURROUND PARAMETER 3 TITLE BAND CH SELECT MENU/GUIDE MODE ENTER SELECT AVR/AVC VIDEO MEMORY STATUS DISPLAY ON SCREEN RETURN 1, 5 Set the slide switch to the position at which the signals were "learned". CD DECK MD MULTI TV VDP VCR SET USE/LEARN T. TONE MULTI SPEAKER DVD SET UP 4 Press the SYSTEM CALL SET button, and hold it in for at least four seconds. · When both the START and LEARNED/TX LEDs light simultaneously, all the stored codes are cleared. Lit DVD 9 OPERATION Before operating 5 Press the USE/LEARN selector button. 1 2 3 Refer to "CONNECTIONS" (pages 6 to 15) and check that all connections are correct. [. . . ] The surround back channel signal is a matrix-encoded signal inserted into both the Dolby Digital SL (surround left) and SR (surround right) channels. Upon playback, the signals are decoded by a high precision digital matrix decoder within the Dolby Digital decoder into the SL, SR and SB channels and output as 6. 1 channels of signals. With the AVR-4800, the signals further undergo Home THX Cinema processing to achieve a THX Surround EX system. Even without the proper environment for playing the SB channel, Dolby Digital Surround EX signals are 100% compatible with existing 5. 1-channel playback systems, so they can be played as such. [. . . ]