User manual DENON AVR-4802

[. . . ] AV SURROUND RECEIVER AVR-4802 OPERATING INSTRUCTIONS MASTER VOLUME INPUT SELECTOR ·)) REMOTE SENSOR SIGNAL DIGITAL INPUT AUTO PCM PURE DIRECT SURROUND BACK CH SIGNAL OUTPUT DETECT VOLUME LEVEL ON/STANDBY ON/STANDBY DTS A B ES DSCRT DVD DIGITAL SURROUND SPEAKER HOME THX CINEMA PURE DIRECT PRECISION AUDIO COMPONENT / AV SURROUND RECEIVER AVR-4802 2 We greatly appreciate your purchase of the AVR-4802. 2 To be sure you take maximum advantage of all the features the AVR-4802 has to offer, read these instructions carefully and use the set properly. Be sure to keep this manual for future reference should any questions or problems arise. "SERIAL NO. PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE CABINET FOR FUTURE REFERENCE" 2 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] NOTES: · The signals of the source selected in the Multi mode are also output from the TAPE and VCR recording output terminals. · Digital signals are not output from the MULTI ZONE audio output jacks. REC / MULTI (Main unit) 37 Playback using the external input (EXT. IN) jacks 1 Set the external input (EXT. IN button on the remote control unit) to switch the external input. EXT. IN (Main unit) (Remote control unit) Once this is selected, the input signals connected to the FRONT-L , FRONT-R, CENTER, SURR. -L (surround left) and SURR. -R (surround right) channels of the EXT. IN jacks are output directly to the front (left and right), center and surround (left and right) speaker systems as well as the pre-out jacks without passing through the surround circuitry. In addition, the signal input to the SW (subwoofer) jack is output to the PRE OUT SW (subwoofer) jack. IN is selected, the input signals connected to the EL (effect left) and ER (effect right) jacks are output to the PRE OUT (SBL and SBR) jacks. 21 2 Cancelling the external input mode To cancel the external input (EXT. IN) setting, press the INPUT MODE or ANALOG button to switch to the desired input mode. INPUT MODE ANALOG 2 2 1 (Main unit) (Remote control unit) · When the input mode is set to the external input (EXT. IN), the play mode (DIRECT, STEREO, DOLBY/DTS SURROUND, HOME THX CINEMA, WIDE SCREEN, 5CH/7CH STEREO or DSP SIMULATION) cannot be set. NOTES: · In play modes other than the external input mode, the signals connected to these jacks cannot be played. In addition, signals cannot be output from channels not connected to the input jacks. · The external input mode can be set for any input source. To watch video while listening to sound, select the input source to which the video signal is connected, then set this mode. 38 Playing audio sources (CDs and DVDs) The AVR-4802 is equipped with three 2-channel playback modes exclusively for music. Select the mode to suit your tastes. 1 PURE DIRECT mode In this mode, the music is played with an extremely high level of sound quality. When this mode is set, all the video-related circuits are turned off so that music signals can be reproduced with high quality. When an analog input (phono, etc. ) is selected, the digital processing circuitry is also turned off to achieve analog sound with even higher purity. PURE DIRECT 1 2 (Main unit) (Remote control unit) SIGNAL DIGITAL PURE DIRECT 3 4 PURE DIRECT display lights. The display is off in the PURE DIRECT mode. 2 DIRECT mode Use this mode to achieve good quality 2-channel sound while watching images. In this mode, the audio signals bypass such circuits as the tone circuit and are transmitted directly, resulting in good quality sound. DIRECT 1 2 3 (Main unit) (Remote control unit) 3 STEREO mode Use this mode to adjust the tone and achieve the desired sound while watching images. STEREO (Main unit) (Remote control unit) 4 VIDEO ON/OFF button When no video signals of a DVD, etc. , are connected to the AVR-4802 and the DVD, etc. , are connected directly to a TV, etc. , the unneeded video circuitry can be turned off by selecting the "VIDEO OFF" setting. VIDEO ON / OFF (Main unit) NOTES: · The system setup function cannot be used when the PURE DIRECT mode is set or the "VIDEO OFF" setting is selected. To use the system setup function, cancel the PURE DIRECT mode or select the "VIDEO ON" setting. · The channel level and surround parameters in the PURE DIRECT mode are the same as in the DIRECT mode. · When the PURE DIRECT button is pressed while in the PURE DIRECT mode, the PURE DIRECT mode is canceled and the DIRECT mode is set. · The crossover frequency setting must be set to "FIXED-THX-" in the system setup in order to turn off the digital circuit when in the analog input mode in the PURE DIRECT mode. [. . . ] Surround EX is a jointly developed technology of THX and Dolby Laboratories, and is a trademark of Dolby Laboratories. Used under authorization. System setup items and default values (set upon shipment from the factory) System setup Speaker Configuration Input the combination of speakers in your system and their corresponding sizes (SMALL for regular speakers, LARGE for fullsize, full-range) to automatically set the composition of the signals output from the speakers and the frequency response. Use this function when using multiple surround speaker combinations for more ideal surround sound. Once the combinations of surround speakers to be used for the different surround modes are preset, the surround speakers are selected automatically according to the surround mode. Surround mode Surround speaker Default settings Front Sp. [. . . ]