User manual DENON AVR-4802R

[. . . ] AV SURROUND RECEIVER AVR-4802R OPERATING INSTRUCTIONS AMP MASTER VOLUME INPUT SELECTOR REMOTE SENSOR SIGNAL DIGITAL INPUT PCM PURE DIRECT SURROUND BACK CH SIGNAL OUTPUT DETECT VOLUME LEVEL ON/STANDBY ON/STANDBY AUTO DTS A B ES DSCRT DVD DIGITAL SURROUND SPEAKER HOME THX CINEMA PURE DIRECT 2 We greatly appreciate your purchase of the AVR-4802R. 2 To be sure you take maximum advantage of all the features the AVR-4802R has to offer, read these instructions carefully and use the set properly. Be sure to keep this manual for future reference should any questions or problems arise. "SERIAL NO. PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE CABINET FOR FUTURE REFERENCE" 2 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] The presence or absence of digital signals is detected, the signals input to the digital input jacks are identified and decoding and playback are performed automatically in DTS, Dolby Digital or PCM (2 channel stereo) format. If no digital signal is being input, the analog input jacks are selected. Use this mode to play Dolby Digital signals. w PCM (exclusive PCM signal playback mode) Decoding and playback are only performed when PCM signals are being input. Note that noise may be generated when using this mode to play signals other than PCM signals. e DTS (exclusive DTS signal playback mode) Decoding and playback are only performed when DTS signals are being input. r ANALOG (exclusive analog audio signal playback mode) The signals input to the analog input jacks are played. IN (external decoder input jack selection mode) The signals being input to the external decoder input jacks are played without passing through the surround circuitry. NOTE: · Note that noise will be output when CDs or LDs recorded in DTS format are played in the "PCM" (exclusive PCM signal playback) or "ANALOG" (exclusive PCM signal playback) mode. Select the AUTO or DTS mode when playing signals recorded in DTS from a laser disc player or CD player. Note on playing a source encoded with DTS · Noise may be generated at the beginning of playback and while searching during DTS playback in the AUTO mode. If so, play in the DTS mode. 2 Select the input mode. · Selecting the analog mode Press the ANALOG button to switch to the analog input. ANALOG (Main unit) (Remote control unit) · Selecting the external input (EXT. IN button on the remote control unit) to switch the external input. EXT. IN (Main unit) (Remote control unit) · Selecting the AUTO, PCM and DTS modes The mode switches as shown below each time the INPUT MODE button is pressed. AUTO PCM DTS INPUT MODE (Main unit) (Remote control unit) 47 3 Select the play mode. Example: Stereo STEREO Input mode display · In the AUTO mode AUTO INPUT MODE PCM DTS One of these lights, depending on the input signal. ANALOG DIGITAL · In the PCM mode AUTO INPUT MODE PCM DTS DIGITAL (Main unit) (Remote control unit) · In the DTS mode AUTO INPUT MODE PCM DTS 4 5 Start playback on the selected component. · For operating instructions, refer to the component's manual. Adjust the volume. MASTER VOLUME DIGITAL · In the ANALOG mode AUTO INPUT MODE PCM DTS ANALOG Input signal display · DOLBY DIGITAL SIGNAL This lights, depending on the input signal. The volume level is displayed on the master volume level display. (Main unit) (Remote control unit) DIGITAL PURE DIRECT PRO LOGIC DIGITAL · DTS SIGNAL DIGITAL PURE DIRECT The volume can be adjusted within the range of ­70 to 0 to 18 dB, in steps of 1 dB. However, when the channel level is set as described on page 23 or page 56, if the volume for any channel is set at +1 dB or greater, the volume cannot be adjusted up to 18 dB. (In this case the maximum volume adjustment range is "18 dB -- (Maximum value of channel level)". ) Input mode when playing DTS sources · Noise will be output if DTS-compatible CDs or LDs are played in the "ANALOG" or "PCM" mode. When playing DTS-compatible sources, be sure to connect the source component to the digital input jacks (OPTICAL/COAXIAL) and set the input mode to "AUTO" or "DTS". DIGITAL SIGNAL DIGITAL PURE DIRECT DIGITAL The DIGITAL indicator lights when digital signals are being input properly. [. . . ] Use this function when using multiple surround speaker combinations for more ideal surround sound. Once the combinations of surround speakers to be used for the different surround modes are preset, the surround speakers are selected automatically according to the surround mode. Surround mode Surround speaker Default settings Front Sp. Small DOLBY/ DTS SURROUND THX / THX 5. 1 Center Sp. Small WIDE SCREEN Subwoofer Yes 5CH/7CH STEREO Surround Sp. [. . . ]