User manual DENON AVR-591 CODES IR

[. . . ] Be sure to keep this manual for future reference should any questions or problems arise. "SERIAL NO. PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE CABINET FOR FUTURE REFERENCE" 2 SAFETY PRECAUTIONS CAUTION TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ATTENTION POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTERODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This device complies with Part 15 of the FCC Rules. [. . . ] Adjust the volume. MASTER VOLUME DIGITAL · When switched to RF in the VDP RF or AUTO mode AUTO INPUT MODE PCM DTS RF DIGITAL · In the ANALOG mode AUTO INPUT MODE PCM DTS RF ANALOG The volume level is displayed on the master volume level display. (Main unit) (Remote control unit) Input signal display · DOLBY DIGITAL INPUTSIGNAL One of these lights, depending on the input signal. The volume can be adjusted within the range of ­60 to 0 to 18 dB, in steps of 1 dB. However, when the channel level is set as described on page 25 or page 42, if the volume for any channel is set at +1 dB or greater, the volume cannot be adjusted up to 18 dB. (In this case the maximum volume adjustment range is "18 dB -- (Maximum value of channel level)". ) Input mode when playing DTS sources · Noise will be output if DTS-compatible CDs or LDs are played in the "ANALOG" or "PCM" mode. When playing DTS-compatible sources, be sure to connect the source component to the digital input jacks (OPTICAL/COAXIAL) and set the input mode to "AUTO" or "DTS". NOTE: · The digital input indicator will light (green) when playing CDROMs containing data other than audio signals, but no sound will be heard. LOCK DIGITAL PRO LOGIC · DTS INPUTSIGNAL LOCK DIGITAL · PCM INPUTSIGNAL LOCK DIGITAL AL24 The AL24 indicator lights when the PURE DIRECT, DIRECT or STEREO mode is selected in the digital input mode. The LOCK LED lights when digital signals are being input properly. If the LED does not light, check whether the digital input component setup (page 28) and connections are correct and whether the component's power is turned on. After starting playback [1] Adjusting the sound quality (tone) The tone control function will not work in the Direct or Home THX Cinema mode. 1 Press the MODE SELECT button and select TONE. The mode switches as follows each time the MODE SELECT button is pressed: MODE SELECT (Main unit) Only displayed when the TUNER input is selected. 2 Select BASS/TREBLE with the FUNCTION knob. FUNCTION 41 2 3 (Main unit) 34 3 Adjust as desired with the CONTROL knob. [5] Checking the currently playing program source, etc. · To increase the bass or treble: Turn the control clockwise. (The bass (Main unit) or treble sound can be increased to up to +12 dB in steps of 2 dB. ) · To decrease the bass or treble: Turn the control counter clockwise. (The bass or treble sound can be decreased to up to ­12 dB in steps of 2 dB. ) 1 1 1 4 If you do not want the bass and treble to be adjusted, turn on the tone defeat mode. The signals do not pass through the bass and treble adjustment circuits, providing higher quality sound. TONE DEFEAT 1 (Main unit) [2] Listening over headphones Plug the headphones' plug into the jack. · The indicator for the selected program source light. · When the AVR-5800 is in the REC OUT mode, the source cannot be output using the M-ZONE 2 buttons on the remote control unit. FUNCTION 1, 2 (Main unit) 1 2 2 Display PHONO CD TUNER AUX DVD / VCR -1 -2 V. AUX MD / VDP TV / DBS TAPE -1 -2 3 Start playing the source to be output. · For operating instructions, refer to the manuals of the respective components. When "M-ZONE 2" is selected for the system setup's multi-zone setting, the source selected here is output from the M-ZONE 2 speaker terminals. The volume can be adjusted and the input source can be selected using the VOLUME UP and VOLUME DOWN buttons on the remote control unit's "M-ZONE 2" page. NOTES: · The signals of the source selected in the M-ZONE-2 mode are also output from the TAPE and VCR recording output terminals. · Digital signals are not output from the MULTI ZONE 1 audio output jacks. 37 Playback using the external input (EXT. IN) jacks 1 Set the external input (EXT. IN button on the remote control unit) to switch the external input. EXT. IN (Main unit) (Remote control unit) The playback switches as shown below each time the button is pressed. EXT. IN-2 Once this is selected, the input signals connected to the FRONT-L , FRONT-R, CENTER, SURR. -L (surround left) and SURR. -R (surround right) channels of the EXT. [. . . ] The result is 360 degrees of movement and moving sound effects that seem to pass right over the listener's head. This system was developed jointly by Lucasfilm THX and Dolby Laboratories, fusing Lucasfilm's idea of improving spatial expression and achieving a uniform 360 degree sound positioning with Dolby Laboratories' matrix encoding technology. Emphasis was placed on compatibility with the existing system Dolby Digital 5. 1-channel, and the new "surround back (SB) channel" was added to achieve improvements over the conventional 5. 1-channel system in terms of the positioning of the sound at the rear, the acoustic image of sound moving from the two sides to the back as well as sound moving from the front to the center rear with the multi surround speaker systems used in movie theaters, thereby enabling various types of surround sound. The surround back channel signal is a matrix-encoded signal inserted into both the Dolby Digital SL (surround left) and SR (surround right) channels. [. . . ]