User manual DENON DN-780R

[. . . ] STEREO CASETTE TAPE DECK DN-780R OPERATING INSTRUCTIONS BEDIENUNGSANLEITUNG MODE D'EMPLOI ISTRUZIONI PER L'USO INSTRUCCIONES DE OPERACION GEBRUIKSAANWIJZING BRUKSANVISNING FOR ENGLISH READERS FÜR DEUTSCHE LESER POUR LES LECTEURS FRANCAIS PER IL LETTORE ITALIANO PARA LECTORES DE ESPAÑOL VOOR NEDERLANDSTALIGE LEZERS FOR SVENSKA LÄSARE PAGE SEITE PAGE PAGINA PAGINA PAGINA SIDA 5 14 23 32 41 50 59 ~ ~ ~ ~ ~ ~ ~ PAGE SEITE PAGE PAGINA PAGINA PAGINA SIDA 13 22 31 40 49 58 67 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN SAFETY INSTRUCTIONS 1. Read Instructions ­ All the safety and operating instructions should be read before the product is operated. Retain Instructions ­ The safety and operating instructions should be retained for future reference. Heed Warnings ­ All warnings on the product and in the operating instructions should be adhered to. [. . . ] · REVIEW close to the beginning of the program or CUE close to the ending. 2 POWER ON PLAYBACK Playback starts automatically when the power is turned on. · Playback is performed according to the reverse mode set when the power was turned off. · Playback is performed even if a cassette tape is only loaded in one deck. · Playback always starts in the "1" tape travel direction. · When tapes are loaded in both Deck A and Deck B, playback starts from Deck A. · The power on playback function can be set with the "PRESET FUNCTION" (page 11). RECORDING · The operations described below apply to deck A and deck B alike. q Press the POWER switch q to the ON ( ¢ ) position. (Check that the erasure prevention tabs of the cassette housing have not been broken off. ) e Select the Dolby NR type that suits the recording. r Select the type of tape transport with the REV. Mode To record on only one side , RELAY or CASCADE Indicator Caution : Be careful not to erase important recordings by mistake. Inadvertent start of recording will happen in the following cases: 1. If the Play ( 0 or 1 ) button is pressed while the 4 indicator lights, recording starts. If the Play ( 0 or 1 ) button and Rec/Rec Mute ( 4 ) button are pressed at the same time, recording starts. The best way to avoid accidental erasure is to break off the two erasure prevention tabs on the cassette housing. 2 PROPER RECORDING LEVEL A too high recording level can saturate the tape and cause distortion. On the other hand, if the recording level is set too low, soft passages will be marked by residual noise. A proper recording level is the most important factor for making well balanced recordings. Guideline for maximum recording level Type I (Normal) Type II (CrO2) Type IV (Metal) +3 dB level on peaks +3 dB level on peaks +3 dB level on peaks To continuously record on both sides t Press the Rec/Rec Mute ( 4 ) button !4 to set the recording pause mode. y Adjust the recording level with the INPUT LEVEL control y while watching the Peak Level Meter. u Recording starts when the Play ( 0 or 1 ) button !4 for the direction indicated by the flashing tape travel indicator ( 0 or 1 ) is pressed. If the other Play ( 0 or 1 ) button !4 is pressed, the direction of tape travel changes. [. . . ] · Do not operate the Master/Slave switches w during synchronized recording. If a Master/Slave switch w is operated, that unit stops. j Press the Stop (2) button !4 on the first unit to stop recording on all the connected units. CASCADE PLAYBACK a Load the cassette tapes you want to play in both decks of all the units and make sure the Dolby NR modes are properly set. MODE button @0 to set the reverse mode of all the units to "CASCADE". [. . . ]