User manual DENON DN-HC4500

[. . . ] USB MIDI / AUDIO INTERFACE & CONTROLLER DN-HC4500 OPERATING INSTRUCTIONS BEDIENUNGSANLEITUNG MODE D'EMPLOI INSTRUCCIONES DE FUNCIONAMIENTO CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. THIS PRODUCT SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. [. . . ] For instructions on operating the DN-D4000/ D4500/BU4500, refer to the respective model's operating instructions. t AC Inlet terminal · Inlet the power cord's plug into DN-HC4500's AC inlet terminal. [When PCDJ connected] Refer to the PCDJ's manual. [When DN-D4500 connected] · TIME: When this button is pressed, the time indicator switches between "ELAPSED" (elapsed time), "REMAIN" (remaining time). · Total: When this button is pushed for more 1 second, you can display the total time. [When PCDJ connected] Refer to the PCDJ's manual. [When DN-D4500 connected] · MEMO: The MEMO mode starts when this button is pushed once in the Cue/Pause mode. · PRESET: When this button is pushed for more than 1 sec, the PRESET mode menu is displayed. y Fader start terminals · Use this when your mixer has the Fader Start function. e USB B terminal · Connect to a computer. · Sends the USB MIDI and HID commands from the DN-HC4500. · Sends the USB audio signals from a PC. u X-CONROL output terminal · Use this when connected to a DENON DNX900 or DN-X500 mixer that offers X-Control. · With the DN-HC4500 it is possible to convert the input fader position into a MIDI signal and send it from the USB terminal. o FLIP/B TRIM [When PCDJ connected] Refer to the PCDJ's manual. [When DN-D4500 connected] · Push this button to switch between the loop mode/hot start mode and stutter mode. · After setting the B point, the B TRIM MODE can be selected. !1 CUE/STUTTER [When PCDJ connected], [When DN-D4500 connected] · Pushing this button in play mode will force the file back to the position which playback started. · In Cue mode, by pushing the CUE button makes a Stutter sound from the Cue point. (Stutter) 3 ENGLISH ENGLISH !2 TITLE [When PCDJ connected] Refer to the PCDJ's manual. [When DN-D4500 connected] · CD TEXT: CD text is displayed. · MP3: The ID3 tag information switches each time the button is pressed. !8 EXIT/RELOOP [When PCDJ connected], [When DN-D4500 connected] · Use this to exit or return back again to Seamless loop playback. You can add variety to looping with this function. @4 PITCH BEND± [When PCDJ connected], [When DN-D4500 connected] · While pushing these buttons will change main playing speed temporarily. · When release button, playing speed returns to the previous speed. #1 EFFECT1 [When PCDJ connected] Refer to the PCDJ's manual. [When DN-D4500 connected] · Turns the Brake mode ON or OFF. #2 FAST SEARCH (6/7) QUICK JUMP [When PCDJ connected], [When DN-D4500 connected] · QUICK JUMP: When one of these buttons is tapped shortly, the playback position jumps in the reverse (6) or forward (7) direction. · FAST SEARCH: When one of these buttons is pressed and held in, the disc is fast-searched in the reverse (6) or forward (7) direction. !9 JOG MODE [When PCDJ connected] Refer to the PCDJ's manual. [When DN-D4500 connected] Select from Bend mode or Manual Frame Search mode. @5 PLAY LIST [When PCDJ connected] Refer to the PCDJ's manual. [When DN-D4500 connected] · Push this butoon to open and close the disc holder. · The disc holder will not open during playback. Stop playback before pushing this button. !3 A1, A2 [When PCDJ connected], [When DN-D4500 connected] · Using this button you can create starting point for Hot Start, Seamless Loop and Stutter. @0 JOG indicator [When PCDJ connected] Refer to the PCDJ's manual. [. . . ] 2 Receive command for VFD Symbol items MIDI command Command 0xBn Number ON TRG : 0x4A OFF TRG : 0x4B Blink ON TRG : 0x4C Value 0x02 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x0D 0x0E 0x0F 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1E 0x24 0x3C 0x25 0x3D 0x26 0x27 0x3B only Use 0x4A (request TRG) only Use 0x4A (request TRG) 0x3C 0x3D DN-HC4500 return pitch slider position DN-HC4500 return XControl fader position Message type Notes MIDI command Command 0xBn Number ON TRG : 0x4D OFF TRG : 0x4E Blink ON TRG : 0x4F Value 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x10 0x11 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F 0x20 only Use 0x4F/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 Message type Data reception LED data reception The panel's LEDs can be set to on, off or blinking by MIDI command, as per the table below. 2 Receive command for LED items VFD Symbol 1 2 3 4 5 6 7 8 9 T. SINGLE BPM m s f Control Change LED 1 2 3 4 5 6 7 8 9 Playlist Pitch match LED JOG mode Green JOG mode Orange Pitch/KEY Green Pitch/KEY Orange TAP Green TAP Orange EFX1/ECHO/LOOP RED Control Change 10 Pitch dot Right 11 Pitch dot center 12 Pitch dot left 13 MP3 14 WAV 15 KB 16 KEY ADJ. 17 MEMO 18 ( : A1 side 19 ( : A2 side 20 ) : A1 side 21 ) : A2 side 22 A1 23 A2 24 B : A1 side 25 B : A2 side 26 Scratch Ring out side 27 Scratch Ring in side 28 Touch dot 29 Track Position Blink 30 Scratch Position 1 (Top right) 31 Scratch Position 2 32 Scratch Position 3 33 Scratch Position 4 34 Scratch Position 5 35 Scratch Position 6 36 Scratch Position 7 10 EFX1 Green 11 EFX2/FLANGER RED 12 EFX2 Green 13 EFX3/FILTER RED 14 EFX3 Green 15 HOT1 16 HOT1 Dimmer 17 HOT2 18 HOT2 Dimmer 19 HOT3 20 HOT3 Dimmer 21 HOT4 22 HOT4 Dimmer 23 HOT5 24 HOT5 Dimmer 25 Parameter KNOB 26 A1 27 A1 Dimmer 28 A2 29 A2 Dimmer 30 Cue 31 Play 32 Jogwheel 33 Pitch slider request 34 X-Control fader request n = MIDI CH 15 ENGLISH ENGLISH VFD parameter data reception Value 0x29 0x2A 0x2B 0x2C 0x2D 0x2E 0x2F 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39 0x3A 0x3B 0x3C 0x3D 0x3E 0x3F 0x40 0x41 10 Segment 1-1 MSB 11 Segment 1-2 MSB 12 Segment 1-3 MSB 13 Segment 1-4 MSB 14 Segment 1-5 MSB 15 Segment 1-6 MSB 16 Segment 1-7 MSB 17 Segment 1-8 MSB 18 Segment 1-9 MSB 19 Segment 1-10 MSB 20 Segment 1-11 MSB 21 Segment 1-12 MSB 22 Segment 1-1 LSB 23 Segment 1-2 LSB 24 Segment 1-3 LSB 25 Segment 1-4 LSB 26 Segment 1-5 LSB 27 Segment 1-6 LSB 28 Segment 1-7 LSB 29 Segment 1-8 LSB 30 Segment 1-9 LSB 31 Segment 1-10 LSB 32 Segment 1-11 LSB 7 8 9 Pitch MSB Pitch LSB Track Position 0x46 0x47 0x48 normal 0x49 reverse 0x01 0x02 0x03 0x04 0x05 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x0D 0x21 0x22 0x23 0x24 0x25 0x27 0x28 0x29 0x2A 0x2B 0x2C 6 Pitch POL 0x45 1 2 3 4 5 Tr number MSB Tr number LSB Time mini Time sec Time frame 0xBn 0x40 0x41 0x42 0x43 0x44 VFD Parameter 0-99 100-109 : "-0" to "-9" 110 : "--", 111 : " " " " 0x00 "+" 0x01 "­" 0x02 0-100% 0x00 ~ 0x0F Control Change Message type items MIDI command Command 0xBn Number ON TRG : 0x4D OFF TRG : 0x4E Blink ON TRG : 0x4F only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E The time-related display and segment display can be set by MIDI command, as per the table below. [. . . ]