User manual DENON DN-X1700

[. . . ] Professional DIGITAL DJ Mixer DN-X1700 Owner's Manual n SAFETY PRECAUTIONS RISK OF ELECTRIC SHOCK DO NOT OPEN FCC INFORMATION (For US customers) 1. PRODUCT This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this product may not cause harmful interference, and (2) this product must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. [. . . ] Also, the EQ control rings light up blue. R2 L/CUE, R/PGM master level meter One of two modes can be selected for display on this meter. Split CUE OFF: The master output audio level is displayed. Split CUE ON: The right channel master CUE (monaural) and left channel CUE (monaural) audio levels are displayed. Getting Started Connections Basic Operations Getting Started Effector Function Fader Start USB Utility Specifications Troubleshooting Q6 CROSSFADER Controls the relative output level from the summed A and B Mixes. When the fader is at its far left, only the A Mix is heard from the Outputs. As the fader is moved toward the right, the amount of B Mix is increased and the amount of A Mix is decreased. When the fader is centered, equal amounts of A and B Mixes are routed to the Outputs. Fully right is all B Mix at the Outputs. W7 Mic EFX INS 1, 2 buttons These buttons enable the various effects of the selected side, either EFX 1 or EFX 2, to be obtained for the mic input signals. E5 Channel input LEVEL controls These are used to adjust the levels of the selected inputs. W8 MIC EQ controls Contour the frequency response of the Mic input ­15 dB to +15 dB. E6 Channel isolator EQ controls (HI, MID, LOW) These are used to change the frequency response of the selected inputs. At the center position, the frequency response is flat. At the ­ position, the frequencies of all the bands are cut off completely. W9 DUCKING ON/OFF button ·UsethistoswitchtheTalkOverfunctionONand OFF (ON/OFF is cyclic) . ·When the button is lit, level of signals except Mics is attenuated. * The ducking attenuation level can be adjusted in the "UTILITY" mode. R3 SIG/PK This is the signal/peak meter for the mic input level. Off: No signals input (under ­60 dB/FS) Green: Signal input (­60 dB/FS to under ­20 dB/FS) Orange: Suitable signal input level (­20 dB/FS to under ­6 dB/FS) Red: Excessively high signal input level (above ­6 dB/ FS) Q7 Channel input fader (CH FADER) Controls the level of the selected Input. Q8 HEADPHONE output jack Accepts 1/4" stereo headphone plugs. E7 CH LEVEL meter Displays the input level after adjusted with LEVEL E5 and Source EQ E6 controls. Q9 HEADPHONE level control Adjusts the volume for the headphones. E0 MIC1, MIC2 TRIM controls Adjusts the level of the Main Mic input. W0 HEADPHONE PAN control This is used to adjust the balance between the CUE sound and the master sound which are monitored using the headphones. E1 MIC1, 2 buttons When the button's LED is lighted, the mic signals take effect. E2 CD/PHONO line input selector buttons These enable the line input of each channel to be selected as CD or PHONO. CD: Rear panel LINE1­4 CD terminal input PHONO: Rear panel LINE1­4 PHONO terminal input W1 SPLIT CUE button There are two headphone monitor modes. Stereo mode (SPLIT CUE OFF): The cue signals and master signals can be monitored in stereo. SPLIT CUE mode: The monaural cue signals are heard through the left channel of the headphones, and the monaural master signals through the right channel. E8 Channel EFX SEND 1, 2 buttons These buttons enable the various effects of the selected side, either EFX 1 or EFX 2, to be obtained for the channel audio signals. The same effect (EFX 1 or 2) can be selected for a multiple number of channels. The LED of the EFX button for the side selected for each channel lights. E9 Channel CUE buttons Pressing in any or all of CUE buttons routes the respective source to the headphone and meter cue sections. Pressing multiple buttons makes it possible to derive mixed sound from the selected sources. *The SOLO mode with no signals mixed can also be selected as a preset. A, B: The channel source is assigned to A or B of the Crossfader. THRU: Select when you don't assign the channel source into the Crossfader. E3 SOURCE W2 CROSSFADER CONTOUR control Allows adjusting the "shape" of the Crossfader response from a gentle curve for smooth, long running fades, to the steep pitch required for top performance cut and scratch effects. SEL LN1/LN2/LN3/LN4/D1­4/USB controls (channel input selector) These enable any of six inputs to be selected for each of the channels. [. . . ] Types of trouble which are not described in the table below may indicate trouble in the unit itself so consult with your dealer from whom you purchased the unit. If your dealer does not know what action to take, contact one of our customer service centers or your nearest repair service center. Cause · The AC power cable is not connected to the power outlet. Remedy · Connect the AC power cable to the power outlet. [. . . ]