User manual DENON DRA-F107

[. . . ] AM-FM STEREO RECEIVER DRA-F107 Owner's Manual Bedienungsanleitung Manuel de l'Utilisateur Manuale delle istruzioni Manual del usuario Gebruiksaanwijzing Bruksanvisning ENGLISH DEUTSCH FRANCAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA n SAFETY PRECAUTIONS RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Read these instructions. Install in accordance with the manufacturer's instructions. [. . . ] · Be sure to connect the left and right channels properly (left with left, right with right). · Do not bundle power cords together with connection cables. Doing so can result in humming or noise. Setup Playback DAB indoor antenna (Supplied) Setting the Timer Assembling the AM loop antenna 1 2 Put the stand section through the bottom of the loop antenna from the rear and bend it forward. into the square hole in the stand. Stand Square hole Loop antenna Projecting part Other Functions Insert the projecting part System Functions n Connecting the AM loop antenna Using the AM Loop Antenna To use suspended on a wall Suspend directly on the wall without assembling. To use standing alone Use the procedure below to assemble. 1 2 3 Push the lever. Insert the conductor. Troubleshooting Specifications Return the lever. NOTE Nail, tack, etc. · Make sure the AM loop antenna lead terminals do not touch metal parts of the panel. · Do not connect two FM antennas simultaneously. ENGLISH Preparations Speaker Connections Speakers (L) (R) Getting Started Connections Setup Playback Setting the Timer Other Functions System Functions Troubleshooting Specifications Cables Used for Connections Select the cables according to the equipment being connected. Connecting the Speaker Cables Carefully check the left (L) and right (R) channels and + (red) and ­ (black) polarities on the speakers being connected to the DRA-F107 , and be sure to interconnect the channels and polarities correctly. Audio cables Analog connections (stereo) (White) (Red) L R L R 1 w q w q Peel off about 10 mm of sheathing from Stereo pin-plug cable Analog connections (for subwoofer) Pin-plug cable Analog connections (for portable player) Stereo mini-plug cable System connections System cable (included with the system device) Speaker connections the tip of the speaker cable, then either twist the core wire tightly or terminate it. the hilt into the speaker terminal. 2 3 4 When using an SC-F107 (speaker system, sold separately), we recommend using the receiver's optimizing filter. Signals adjusted for the SC-F107's properties are output. " Turn the speaker terminal counterclockwise Insert the speaker cable's core wire to Turn the speaker terminal clockwise to tighten it. NOTE · Use speakers with an impedance of 4 to 16 /ohms. The protection circuit may be activated if speakers with an impedance other than specified are used. · Connect the speaker cables in such a way that they do not stick out of the speaker terminals. The protection circuit may be activated if the core wires touch the rear panel or if the + and ­ sides touch each other (v "Protection circuit"). · Never touch the speaker terminals while the power supply is connected. Doing so could result in electric shock. Speaker cables Protection circuit The protection circuit will be activated in the following cases: · When the speaker cable's core wires are touching the rear panel or screws or when the speaker cable's + and ­ sides are touching · When the surrounding temperature is extremely high · When the internal temperature rises due to extended use with a high output When the protection circuit is activated, the speaker output is cut off and the power indicator flashes orange. If this happens, unplug the power cord, then check the connections of the speaker cables and input cables. If the set's temperature is extremely high, wait for it to cool off and improve surrounding ventilation. After doing this, plug the power cord back in. If the protection circuit is activated though there are no problems in ventilation around the set or in connections, the set could be damaged. Turn off the power, then contact a DENON servicing and inquiry outlet. ENGLISH Connecting a subwoofer Power amp / Subwoofer Connecting the Playback Components CD Player CD Player Getting Started Record Player Turntable Connections Setup L R Playback Ground wire L R R L Setting the Timer Other Functions When connecting the DRA-F107 and DCD-F107 (CD player, sold separately), make system connections. This enables operation using the DRA-F107's remote control unit and the various system functions. (vpage 22 "About System Functions") System Functions · Playback with an MC cartridge is not possible with the DRA-F107 . [. . . ] properly when · You are operating outside of the remote control specified range. · Obstacle between main unit and remote control unit. · The batteries are not inserted in the proper direction, as indicated by the polarity marks in the battery compartment. · The set's remote control sensor is exposed to strong light (direct sunlight, inverter type fluorescent bulb light, etc. ). [. . . ]