User manual DENON POA-T10

[. . . ] Be sure to keep this manual for future reference should any questions or problems arise. "SERIAL NO. PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE CABINET FOR FUTURE REFERENCE" 2 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ATTENTION POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTERODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This device complies with Part 15 of the FCC Rules. [. . . ] Video deck (VCR) system buttons SYSTEM CALL POWER 4. Monitor TV system buttons SYSTEM CALL POWER SET DVD CALL VDP OFF TUNER ON / SOURCE SHIFT SET DVD CALL VDP OFF TUNER ON / SOURCE SHIFT SET DVD CALL VDP OFF TUNER ON / SOURCE SHIFT 1 TV/DBS 2 V. AUX 3 PHONO 1 TV/DBS 2 V. AUX 3 PHONO 1 TV/DBS 2 V. AUX 3 PHONO 4 VCR-1 5 CD 6 MD / TAPE-1 CHANNEL 4 VCR-1 5 CD 6 MD / TAPE-1 CHANNEL 4 VCR-1 5 CD 6 MD / TAPE-1 CHANNEL 7 VCR-2 8 0 9 TAPE-2 MON TV/VCR 7 VCR-2 8 0 9 TAPE-2 MON TV/VCR 7 VCR-2 8 0 9 TAPE-2 MON TV/VCR +10 A/B +10 A/B +10 A/B VOLUME DISC SKIP+ VOLUME DISC SKIP+ VOLUME DISC SKIP+ POWER 6, 7 2 1 8, 9 3 : Power on/off : Manual search (forward and reverse) : Stop : Play : Auto search (cue) : Pause POWER 6, 7 2 1 3 CHANNEL +, ­ : Power on/off : Manual search (forward and reverse) : Stop : Play : Pause : Switch channel POWER VOLUME ·, ª TV/VCR CHANNEL +, ­ : Power on/off : Volume up/down : Switch between TV and VCR : Switch channel 35 Learning function · If your AV component is not a DENON product or it cannot be operated with the preset memory codesets, you can "teach" the POA-T10's remote control to "learn" the codes from the component's original remote control. · The buttons that can be "learned" are the CD, DECK and MD system buttons (see page 32) and the DVD, VDP, VCR and TV system buttons (see page 35). (For the CD, MD, DVD, VDP and TV, the A block buttons can also be "learned", and for the DVD and TV, the B block buttons can also be "learned". ) SET DVD CALL VDP OFF TUNER ON / SOURCE SHIFT 1 2 V. AUX 3 PHONO 1 Press the USE/LEARN selector button with the tip of a pen etc. , to set the learn mode. Both the START and LEARNED/TX indicators flash. Flashes A TV/DBS 4 VCR-1 5 CD 6 MD / TAPE-1 CHANNEL 7 VCR-2 8 0 9 TAPE-2 MON TV/VCR +10 A/B 4 VOLUME DISC SKIP+ HOME THX CINEMA DOLBY / DTS SURROUND DIRECT DSP SIMULATION 5CH / 7CH STEREO STEREO MASTER VOL. INPUT MODE ANALOG EXT. IN This unit's remote control unitFlashes 2 AUDIO AVR/AVC VIDEO CD DECK MD MULTI TV MUTING DVD VDP VCR SYSTEM SETUP TUNING SURROUND PARAMETER 3 B TITLE BAND CH SELECT MENU/GUIDE MODE ENTER SELECT 2 3 4 Set the program switch to the side to be "learned". Set to the AUDIO side for the CD, tape deck or DAT position, to the VIDEO side for the VDP, VCR or TV position. AUDIO AVR/AVC VIDEO MEMORY STATUS DISPLAY ON SCREEN RETURN 1, 8 USE/LEARN T. TONE MULTI SPEAKER DVD SET UP 5 Check that the START LED is lit, then press the button to be "learned" on the other remote control unit. Other remote control unit Set the program switch to the position to be "learned". DECK MD CD MULTI DVD VDP VCR TV This unit's remote control unitFlashes Set the remote control units so they are facing each other, then press the button to be "learned" on this unit's remote control unit. Transmitting windows Lit Other remote control unit 6 Once the START LED turns off and the LEARNED/TX LED lights, release the button on the other remote control unit. This unit's remote control unitFlashes Approx. 5 cm The two LEDs start flashing again. Lit The indicator stops flashing and the START LED lights. The learnable buttons are the buttons which can be operated with the DENON system codes for the CD player, DAT and tape deck, the buttons which can be operated with the preset memory for the VCR, VDP and TV. For the TV only, however, the buttons in the section indicated "A" on the diagram above can also be "learned". · The LEARNED/TX LED does not light if system call signals cannot be stored at the button that you have pressed or if you have already stored the maximum number of signals. 38 Clearing "learned" remote control signals 1 Press the USE/LEARN selector button with the tip of a pen, etc. , to set the learn mode. 4 START SYSTEM CALL LEARNED/TX POWER SET DVD CALL VDP OFF TUNER ON / SOURCE SHIFT 1 TV/DBS 2 V. AUX 3 PHONO 4 VCR-1 5 CD 6 MD / TAPE-1 CHANNEL 7 VCR-2 8 0 9 TAPE-2 MON TV/VCR +10 A/B VOLUME DISC SKIP+ HOME THX CINEMA DOLBY / DTS SURROUND DIRECT DSP SIMULATION 5CH / 7CH STEREO STEREO MASTER VOL. INPUT MODE ANALOG EXT. IN 2 3 To clear "learned" remote control signals, set the slide switch to the position at which the signals were "learned". AUDIO 2 AUDIO AVR/AVC VIDEO CD DECK MD MULTI TV MUTING DVD VDP VCR SYSTEM SETUP TUNING SURROUND PARAMETER 3 TITLE BAND CH SELECT MENU/GUIDE MODE ENTER SELECT AVR/AVC VIDEO MEMORY STATUS DISPLAY ON SCREEN RETURN 1, 5 Set the slide switch to the position at which the signals were "learned". CD DECK MD MULTI TV VDP VCR SET USE/LEARN T. TONE MULTI SPEAKER DVD SET UP 4 Press the SYSTEM CALL SET button, and hold it in for at least four seconds. · When both the START and LEARNED/TX LEDs light simultaneously, all the stored codes are cleared. Lit DVD 9 OPERATION Before operating 5 Press the USE/LEARN selector button. 1 2 3 Refer to "CONNECTIONS" (pages 6 to 15) and check that all connections are correct. Set the remote control unit's slide switch to the AUDIO position. (only when operating with the remote control unit) AUDIO AVR/AVC VIDEO 3 Turn on the power. Press the POWER operation switch (button). ON / STANDBY START SYSTEM CALL LEARNED/TX POWER RC-869 ON / SOURCE SHIFT SET DVD CALL VDP OFF TUNER 3 1 TV/DBS 2 V. AUX 3 PHONO 4 5 CD 6 MD / TAPE-1 CHANNEL ON / SOURCE VCR-1 Lights ON/STANDBY 7 VCR-2 8 0 9 TAPE-2 MON TV/VCR +10 A/B VOLUME DISC SKIP+ (Main unit) (Remote control unit) HOME THX CINEMA DOLBY / DTS SURROUND DIRECT DSP SIMULATION 5CH / 7CH STEREO STEREO MASTER VOL. · When pressed, the power turns on and the display lights. The sound is muted for several seconds, after whitch the unit operates normally. · When pressed again, the power turns off, the standby mode is set and the display turns off. · Whenever the ON/STANDBY button is in the STANDBY state, the apparatus is still connect on AC line voltage. Please be sure to unplug the cord when you leave home for, say, a vacation. INPUT MODE ANALOG EXT. IN 2 AUDIO AVR/AVC VIDEO CD DECK MD MULTI TV MUTING DVD VDP VCR SYSTEM SETUP TUNING SURROUND PARAMETER 39 Playing the input source 1 3 5 1 START SYSTEM CALL LEARNED/TX POWER RC-869 ON / SOURCE SHIFT SET DVD CALL VDP OFF TUNER 1 TV/DBS 2 V. AUX 3 PHONO 4 VCR-1 5 CD 6 MD / TAPE-1 CHANNEL 7 VCR-2 8 0 9 TAPE-2 MON TV/VCR +10 A/B VOLUME DISC SKIP+ HOME THX CINEMA DOLBY / DTS SURROUND DIRECT 2 3 2 DSP SIMULATION 5CH / 7CH STEREO STEREO MASTER VOL. 5 MUTING INPUT MODE ANALOG EXT. IN AUDIO AVR/AVC VIDEO CD DECK MD MULTI TV VDP VCR DVD SYSTEM SETUP TUNING SURROUND PARAMETER 1 Select the input source to be played. Example: CD INPUT SELECTOR CD 8 (Main unit) (Remote control unit) TAPE-2 MON When the tape 2 input (TAPE-2 MON) is selected, the input indicator lights. Lit 2 Select the input mode. · Selecting the analog mode Press the ANALOG button to switch to the analog input. ANALOG ANALOG (Main unit) (Remote control unit) · Selecting the external input (6CH/8CH EXT. [. . . ] "Dolby Digital Surround EX" is a new movie sound track that greatly enhances the sense of spatial expression and the positioning of the surround channel sound. The result is 360 degrees of movement and moving sound effects that seem to pass right over the listener's head. This system was developed jointly by Lucasfilm THX and Dolby Laboratories, fusing Lucasfilm's idea of improving spatial expression and achieving a uniform 360 degree sound positioning with Dolby Laboratories' matrix encoding technology. Emphasis was placed on compatibility with the existing system Dolby Digital 5. 1-channel, and the new "surround back (SB) channel" was added to achieve improvements over the conventional 5. 1-channel system in terms of the positioning of the sound at the rear, the acoustic image of sound moving from the two sides to the back as well as sound moving from the front to the center rear with the multi surround speaker systems used in movie theaters, thereby enabling various types of surround sound. [. . . ]