User manual DIGITECH GNX2

[. . . ] GENETX TM GUITAR PROCESSOR USER'S GUIDE Warning For your protection, please read the following: Water and Moisture: Appliances should not be used near water (e. g. near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. ) Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. These symbols are internationally accepted symbols that warn of potential hazards with electrical products. The lightning flash means that there are dangerous voltages present within the unit. The exclamation point indicates that it is necessary for the user to refer to the owners manual. These symbols warn that there are no user serviceable parts inside the unit. [. . . ] The TalkerTM must have an appropriate input level from your microphone in order to work properly. If the microphone input is too weak, the TalkerTM will have trouble tracking. If the input is too strong, the TalkerTM will clip making the words unintelligible. The Mic Sensitivity ranges from 1 being the least sensitive to 99 being the most sensitive. Chorus/Mod Effects The Modulation Effects group is a multi-function module allowing you to select effects such as; Chorus, Flanger, Phaser, Triggered Flanger, Triggered Phaser, Tremolo, Panner, Vibrato, Rotary Speaker, AutoYaTM, YaYaTM, SynthTalkTM, Envelope Filter (auto wah), Detune, and Pitch Shift. Only one of the effects in this row can be used at a time. When the Chorus/Mod group is selected, the Status button is used to turn the Effect (effect) module on and off. The Number 1 knob is used to select the type of effect. After selecting the type of effect in this module, the Number 2-5 knobs can then be used to adjust the individual parameters associated with the selected effect. The following pages describe each effect and their parameters in more detail. CHORUS (CHORUS) A Chorus adds a short delay to your signal. The delayed signal is modulated in and out of tune and then mixed back with the original signal to create a thicker sound. Parameter 1 - The Number 2 knob adjusts the rate (Speed) of the modulation. * These Parameters are only available using the GenEditTM computer editor software. 22 Effects and Parameters Parameter 2 - The Number 3 knob adjusts the intensity (Depth) of the modulation. Parameter 3 - The Number 4 knob adjusts the PreDelay (PREDeLaY) or length of time before the Chorus effect is applied to the input signal. * Parameter 4 - Selects the waveform used by the Chorus. Waveforms include: Triangle , Sine, and Square. * Parameter 5 - Adjusts the left to right balance of the wet signal. Mod Level - The Number 5 knob controls the level (mod levl) of the Chorus. FLANGER ( flanger) A Flanger uses the same principle as a Chorus but uses a shorter delay time and adds regeneration (or repeats) to the modulating delay. This results in an exaggerated up and down sweeping motion to the effect. Parameter 1 - The Number 2 knob adjusts the rate (Speed) of the modulation. Parameter 2 - The Number 3 knob adjusts the intensity (Depth) of the Modulation. Parameter 3 - The Number 4 knob adjusts the amount of feedback (Regen) added to the Flanger delay. * Parameter 4 - Selects the waveform used by the Flanger. Waveforms include: Triangle , Sine, and Square. * Parameter 5 - Adjusts the left to right balance of the wet signal. Mod Mix - The Number 5 knob controls the mix (mod mix) of wet and dry signal. Ranges from 0 (all dry) to 99 (all wet). [. . . ] Using the FX MODE or RHYTHM buttons, scroll to the left or right until drytrack (Dry Track) is displayed. Rotate the DATA WHEEL to select OF (disabled), 1 (Dry Track 1), or 2 (Dry Track 2). Factory Reset This function resets the GNX2 settings to its original factory settings. This procedure erases ALL custom user presets, utility settings, and recalibration of the Expression Pedal. The procedure for performing a Factory Reset is as follows: NOTE: Performing this function will erase all user-programmed data. [. . . ]