User manual DIGITECH GNX4

[. . . ] IMPORTANT SAFETY INSTRUCTIONS WARNING FOR YOUR PROTECTION PLEASE READ THE FOLLOWING: KEEP THESE INSTRUCTIONS HEED ALL WARNINGS FOLLOW ALL INSTRUCTIONS DO NOT USE THIS APPARATUS NEAR WATER The symbols shown above are internationally accepted symbols that warn of potential hazards with electrical products. The lightning flash with arrowpoint in an equilateral triangle means that there are dangerous voltages present within the unit. The exclamation point in an equilateral triangle indicates that it is necessary for the user to refer to the owner's manual. These symbols warn that there are no user serviceable parts inside the unit. [. . . ] Select a User or Card Preset Using the Data Wheel 5 Press Store Again 7. Press Store Again Copying a Preset To copy one preset to another preset location, begin by selecting the preset you want to copy, then follow the steps listed above. Press EXIT at any time during the procedure to abort the store process. 58 Footswitch Functions for Modes The GNX4's Footswitches perform different functions specific to the Mode that has been selected. Listed below are descriptions of each footswitch's function within each of the three Modes. Preset Mode - Green Bank Up Footswitch - Selects the next bank of presets. Pressing and holding this footswitch scrolls up through banks. When a new bank is selected the 1 through 5 footswitch LEDs will strobe left to right prompting the user to select a preset. If a preset is not selected within 5 seconds, the GNX4 returns to the currently selected bank and preset. Pressing and holding both the Bank Up and Bank Down Footswitches together will temporarily enable both footswitches to navigate through the GNX4's drum patterns or user MIDI files and MP3s stored on an optional CF card. Bank Down Footswitch - Selects the previous bank of presets. Pressing and holding this footswitch scrolls down through banks. When a new bank is selected the 1 through 5 footswitch LEDs will strobe left to right prompting the user to select a preset. If a preset is not selected within 5 seconds, the GNX4 returns to the currently selected bank and preset. Pressing and holding both the Bank Up and Bank Down Footswitches together will temporarily enable both footswitches to navigate through the GNX4's drum patterns or user MIDI files and MP3s stored on an optional CF card. AMP CHANNEL Footswitch 1 - Selects the first preset in the active bank. A second press puts the GNX4 into Bypass or selects the previous preset if Preset Bounceback is enabled (see page 22 for more instructions on the Preset Bounceback function). Pressing and holding Footswitches 1 and 2 together will enable or disable the Drums/MP3 Sync button in the Recorder Panel. CONTROL A Footswitch 2 - Selects the second preset within the active bank. A second press puts the GNX4 into Bypass or selects the previous preset if Preset Bounceback is enabled (see 22 for more instructions on the Preset Bounceback function). Pressing and holding Footswitches 1 and 2 together will enable or disable the Drums/MP3 Sync button in the Recorder Panel. Pressing and holding Footswitches 2 and 3 together will bypass the GNX4's effects and amp models. Footswitch 3 - Selects the third preset in the active bank. A second press puts the GNX4 into Bypass or selects the previous preset if Preset Bounceback is enabled (see 22 for more instructions on the Preset Bounceback function). Pressing and holding Footswitches 2 and 3 together will bypass the GNX4's effects and amp models. Pressing and holding Footswitches 3 and 4 together accesses the Tuner. CONTROL B CONTROL C Footswitch 4 - Selects the fourth preset in the active Bank. A second press puts the GNX4 into Bypass or selects the previous preset if Preset Bounceback is enabled (see 22 for more instructions on the Preset Bounceback function). [. . . ] Go to Options->Audio->Input Monitoring to disable. · Make sure the GNX4 is the playback device, not your internal sound card. · Make sure mic signal routing is set to mic dry, mic rvb, or mic fx and that CF/USB 1-2 or USB 3-4 sources are set to one of the following : steroall, mono all, sum+dgtr, sum+mic, dgtr+mic, or dry mic. · Make sure steroall, mono all, drums st or drums mn is selected as source for CF/USB 1-2 or USB 3-4. [. . . ]