User manual DIGITECH JAMMAN

[. . . ] Owner's Manual Professional Audio Equipment IMPORTANT SAFETY INFORMATION WarnInG for your ProtectIon reaD tHe foLLoWInG: KEEP THESE INSTRUCTIONS HEED ALL WARNINGS the symbols shown above are internationally accepted symbols that warn of potential hazards with electrical products. the lightning flash with arrowpoint in an equilateral triangle means that there are dangerous voltages present within the unit. the exclamation point in an equilateral triangle indicates that it is necessary for the user to refer to the owner's manual. these symbols warn that there are no user serviceable parts inside the unit. [. . . ] When the Repeats knob is set to the maximum setting, these delays can become unstable just like the actual delays they were modeled from do. The Modulation parameter adds chorusing or a vibrato effect to the delay. The first half of the knob range is chorusing with increasing depth. The second half of the knob range is vibrato with increasing depth. 27 Storing and Recalling Delay Settings The JamMan® Delay's delay settings can be stored to any of the numbered footswitches allowing instant recall of these settings during performance. When delay settings are modified by turning the knobs, the DeLaY StoRe button will light. To store modified settings to the footswitches, follow these steps: 1. This button will now be lit and the DeLaY footSWItcHeS will begin flashing. Press any flashing DeLaY footSWItcH to store the settings to that footswitch (or press the DeLaY StoRe button again to store the settings to the currently active DeLaY footSWItcH). The DeLaY StoRe button will turn off and the active footswitch will stop flashing and light solid to indicate the new settings have now been stored to this location. To recall stored delay settings, press the DeLaY footSWItcH they were stored to. You can also store delay settings during live performance (such as a new tapped tempo) by pressing and holding the active delay memory footswitch for 3 seconds. NOTE: Delay settings cannot be edited or stored when the delay effect is bypassed. 28 Storing and Recalling Delay Settings 2 1 29 Setting Delay Time with the Delay Tempo Footswitch The JamMan® Delay's delay has a Tempo footswitch that can be used for setting the delay time by tapping in the rhythm. Step on a DeLaY footSWItcH to enable a delay preset. Press the DeLaY teMPo footswitch in time with the music to adjust the delay time. Tempo works in conjunction with the Multiplier button so you can tap in quarter notes but get variations on the delay time depending on which Multiplier is selected. 30 Setting Delay Time with the Delay Tempo Footswitch 1 2 31 Synchronizing Delay Tempo to Loop Tempo The JamMan® Delay's delay time can be synchronized with the Looper's tempo. This is an extremely useful feature that allows the delay time to be automatically set based on the tempo of any loop that is playing. To enable Delay Tempo synchronization, follow these steps: 1. Press and hold the DeLaY teMPo footswitch for 2 seconds until its LED stops flashing and lights solid red (this indicates Delay Tempo Sync mode). You can now use the looper's teMPo/StoP footswitch to tap in the tempo for both the loop and the delay. When Delay Tempo Sync mode is active, you can change loops and the delay Tempo will automatically be set to the loop's tempo. This ensures your delay time will always be synced with the loop that is playing. To exit Delay Tempo Sync mode, simply tap the delay Tempo footswitch once or turn the Time knob. Another feature that can be used when Delay Tempo Sync is enabled is a 6th Multiplier. While Sync is enabled, press the MULtIPLIeR button until all MULtIPLIeR LEDs light. [. . . ] and the LooP StoRe button will continue to flash. You can press the SetUP button to abort the procedure. To initiate the card formatting procedure, press and hold the LooP StoRe button for two seconds. The DISPLaY will show Bu indicating the card is being formatted. Once completed, the DISPLaY will read 1 and the card is now ready for recording. 65 Erase All Loops - Memory Card The Erase Loops procedure only erases JamMan® Delay loop data from a memory card. [. . . ]