User manual DIGITECH RP200A

[. . . ] User's Guide Warning - For Your Protection: 1. Install in accordance with the manufacturer's. This appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. Do not defeat the safety purpose of the polarized our grounding-type plug. [. . . ] Understanding how these Effects will alter the sound, and how each Parameter will alter the Effect will help you achieve the sound you are looking for. The following overview of the RP200 Artist's Effects outlines what each Effect and Parameter does. 15 Pickup/Wah The Pickup Simulator provides the thick tone of a humbucker pickup to a guitar with single coil pickups, or the bright edgy sound of a single coil pickup to a guitar with a humbucker. This allows you to have the best of both worlds without having to change guitars during a performance. Wah is an effect controlled by an Expression Pedal making the guitar sound as if it's saying "Wah. " Pickup Type - The Parameter 1 knob selects the Pick Up type which will be simulated. Values include: PCk Of (Turns the Pickup Simulator off), SC>HUM (Gives a single coil pick up the warm tone of a humbucker), and HUM>SC (Gives a humbucker the unique sound of a single coil). Wah Type - The Parameter 2 knob selects the Wah Type. Values include: WaH Of (Turns the Wah Effect off), CRY (Cry Wah is a traditional sounding Wah), BOUTIQ (Boutique Wah is a wide sweeping Wah with a more modern sound) and FULRNG (Full Range Wah sweeps the entire spectrum of audible frequencies). Wah Position - The Parameter 3 knob adjusts the Wah Pedal Position. Ranges from 1 (toe up) to 99 (toe down). Compressor A Compressor is used to increase sustain, tighten up guitars, and prevent the signal from clipping the input of other effects. It sets a maximum boundary for the strength of a signal. Comp Type - The Parameter 1 Adjusts the length of time it takes for the Compressor to respond to a signal exceeding the boundary. Values include: Cmp Of (Turns the Compressor off) to fast, meDIUM, and slOw. 16 Amount - The Parameter 2 knob adjusts the Amount of Compression (ratio and sustain) and ranges from 1 (slight compression) through 20 (maximum sustain). Gain - The Parameter 3 knob adjusts the Output Gain from the Compressor. Ranges from 0 to 6. Amp Modeling Amp Modeling is a technology which applies the tone of several popular modern and vintage amps. Amp Modeling also includes an acoustic guitar simulation. Amp Type - The Parameter 1 knob selects the 12 types of Amp Models. amp Of - Turns the modeling off BLKFAC - Based on a `65 Fender Twin Reverb BOUTIQ - Based on a Matchless DC30 RECTIF - Based on a Mesa Dual Rectifier HOTROD - Based on a Mesa Boogie Mark II C tweeD - Based on a `57 Fender Tweed Deluxe CLEAN1 - Based on a Vox AC30 top boost CLEAN2 - A clean tube combo setting STACK - Based on a `78 Marshall Master Volume CRUNCH - A nice crunchy combo HIGAIN - Based on a Marshall JCM900 FUZZ - A vintage fuzz distortion ACOUST - A flat top acoustic guitar Marshall® is a registered trademark of Marshall Amplification Plc. Vox® is a registered trademark of Korg UK. Fender, Matchless, and Mesa Boogie, are trademarks of their respective companies and are in no way associated with DigiTech. Amp Gain - The Parameter 2 knob adjusts the Gain (distortion) for the selected Amp Model (not available for Acoustic). The Gain parameter ranges from 0 to 99. Amp Level - The Parameter 3 knob adjusts the Level (volume) of the selected Amp Model. The Level parameter ranges from 0 to 99. 17 EQ Equalization is an extremely useful tool used to further shape the tonal response of your guitar signal. The EQ in the RP200 Artist is similar to the tone knobs on an amplifier. All three EQ parameters range from -12dB to +12 dB. Bass - The Parameter 1 knob adjusts the amount of low end enhancement (Bass). MiD - The Parameter 2 knob adjusts the amount of mid range enhancement. TReB - The Parameter 3 knob adjusts the amount of high end enhancement (Treble). Cabinet/Gate The Cabinet Modeling simulates different types of miked speaker cabinets. You have your choice of 3 Cabinet Types and 4 Mic Placements in relationship to the speaker cabinet. A Noise Gate is designed to eliminate noise while you are not playing. Cabinet/Mic - The Parameter 1 knob selects the type of simulated Speaker cabinet and mic placement in relation to the speaker. CAB OF - Cabinet Off DARK 1 - Dark 4x12 Mic DARK 2 - Dark 4x12 Mic DARK 3 - Dark 4x12 Mic DARK 4 - Dark 4x12 Mic BRIT BRIT BRIT BRIT 1 2 3 4 1 2 3 4 WARM WARM WARM WARM 1 2 3 4 - Warm - Warm - Warm - Warm 4x12 4x12 4x12 4x12 Mic Mic Mic Mic 1 2 3 4 - Bright Bright Bright Bright 2x12 2x12 2x12 2x12 Mic Mic Mic Mic 1 2 3 4 18 Gate Type - The Parameter 2 knob selects between the Silencer TM Noise Gate, or the Auto Swell volume swell effect. Values include: Gat Of (Turns the Noise Gate off), silNCR (Selects the SilencerTM Noise Gate) and swEl1 through swEl9 (Selects the Auto Swell volume swell effect. [. . . ] Rotate the Parameter 2 knob to select the minimum value the assigned parameter will reach with the Expression Pedal in the toe up position (not available when volume is the assigned parameter). Rotate the Parameter 3 knob to select the maximum value the assigned parameter will reach with the Expression Pedal in the toe down position (not available when volume is the assigned parameter). Store your Expression Pedal assignment to your Preset. See page 13 for more information on the storing procedure. 28 Factory Reset This function resets the RP200 Artist to its original factory settings. This procedure will erase all custom user Presets, and recalibrate the Expression Pedal. [. . . ]