User manual DIGITECH RP250

[. . . ] Modeling Guitar Processor User's Manual DECLARATION OF CONFORMITY Manufacturer's Name: Manufacturer's Address: declares that the product: Product name: Note: Product option: DigiTech 8760 S. Sandy Parkway Sandy, Utah 84070, USA RP250 Product name may be suffixed by the letters EX, EU, JA, and UK. all (requires Class II power adapter that conforms to the requirements of EN60065, EN60742, or equivalent. ) conforms to the following Product Specifications: Safety: EMC: Supplementary Information: The product herewith complies with the requirements of the Low Voltage Directive 72/23/EEC and the EMC Directive 89/336/EEC as amended by Directive 93/68/EEC. Vice-President of Engineering-MI 8760 S. [. . . ] The RP250 has placed the Amp and Effect models in an order for optimum results. The following diagram shows the order in which they are connected. Pickup Simulator Wah Compressor Chorus/ Modulation (Whammy) Distortion Amp Modeling EQ Cabinet Model Noise Gate Volume Pre Chorus/ Modulation Delay Reverb Volume Post 19 Model Definitions Each Amp and Effect model within the RP250 can be programmed to suit your personal taste and application. Understanding how these components alter the sound, and how each parameter alters the effect, will help you achieve the sound you are looking for. The following overview of the RP250's effects outlines what each effect and parameter does. Pickup The Pickup Simulator provides the thick tone of a humbucker pickup to a guitar with single coil pickups, or the bright, edgy sound of a single coil pickup to a guitar with a humbucker. This gives you the best of both worlds without having to change guitars during a performance. Pickup Model - Knob 1 selects the Pickup model to be simulated. Values include: SC>Hb (gives a single coil pickup the warm tone of a humbucker), and Hb>SC (gives a humbucker the unique sound of a single coil). Press this knob to turn Pickup modeling on and off. Preset Level - Knob 4 adjusts the preset's level. Wah Wah is an effect controlled by an Expression Pedal making the guitar sound as if it's saying "Wah. " Wah Model - Knob 1 selects the Wah model. Values include: FuLrnG (DigiTech® Full Range Wah sweeps the entire spectrum of audible frequencies), CrYwah (Cry Wah is a traditional sounding Wah), and clyde(based on a Vox® Clyde McCoyTM Wah). Press this knob to turn Wah models on and off. Wah Minimum - Knob 2 adjusts the Wah Pedal Minimum. Ranges from 0 (toe up) to 99 (toe down). 20 Wah Maximum - Knob 3 adjusts the Wah Pedal Maximum. Ranges from 0 (toe up) to 99 (toe down). Wah Level - Knob 4 adjusts the Wah Level. Ranges from 0dB to +12dB. Compressor A Compressor is used to increase sustain, tighten up guitars, and prevent the signal from clipping the input of other effects. It sets a maximum boundary for the strength of a signal. Comp Model - Knob 1 selects one of two Compressor models: DIGCMP (DigiTech® Compressor) or CSCOMP (Based on a Boss® CS-2 Compressor/Sustainer). Press this knob to turn the selected Compressor models on and off. Sustain - Knob 2 adjusts the amount of sustain. Tone/Attack - Knob 3 adjusts the tone for the DigiTech Compressor, or attack for the Boss CS-2. Compressor Level - Knob 4 adjusts the Level from the Compressor. Attack (X-EditTM only for DigiComp) - Knob 4 adjusts the amount of time the Compressor takes to respond to a signal that exceeds the threshold. [. . . ] Be sure you want to erase the memory and start fresh before continuing with this procedure. The procedure for performing a Factory Reset is as follows: 1. Press and hold the Store button while powering up the RP250. When the display prompts you with FACrSt, release the Store button, which is now flashing. [. . . ]