User manual DIGITECH RP355_E REV 18-6412V-D

[. . . ] Modeling Guitar Processor Owner's Manual Professional Audio Equipment 1 WARNING FOR YOUR PROTECTION READ THE FOLLOWING: KEEP THESE INSTRUCTIONS The symbols shown above are internationally accepted symbols that warn of potential hazards with electrical products. The lightning flash with arrowpoint in an equilateral triangle means that there are dangerous voltages present within the unit. The exclamation point in an equilateral triangle indicates that it is necessary for the user to refer to the owner's manual. These symbols warn that there are no user serviceable parts inside the unit. [. . . ] Wah Minimum - Knob 2 adjusts the Wah Pedal Minimum. Ranges from 0 (toe up) to 99 (toe down). WahMaximum-Knob3 adjusts the Wah Pedal Maximum. Ranges from 0 (toe up) to 99 (toe down). Wah Level - Knob 6 adjusts the Wah Level. Ranges from 0dB to +12dB. 13 A Compressor is used to increase sustain, tighten up guitars, and prevent the signal from clipping the input of other effects. It sets a maximum boundary for the strength of a signal. Comp Model - Knob 1 selects one of three Compressor models: DIGCMP (DigiTech® Compressor), CSCOMP (Based on a Boss® CS-2 Compressor/Sustainer), or DYnCOMP (Based on an MXR® Dynacomp). Press this knob to turn the selected Compressor model on and off. Knobs 2-6 have the following functions for the various Compressor models: Compressor Model digcmp cscomp dyncmp Knob 2 (Sustain) Sustain Sustain Sensitivity Knob3 (Tone) Tone --Knob 4 (Attack) Attack Attack -Knob5 Knob 6 (Compressor Level) Level Level Output Compressor ---- Distortion The RP355 models the tones of 18 popular distortion stompboxes, each of which can be tweaked and modified, just like the real thing. Distortion Model - Knob 1 selects one of the selected Distortion model on and off. scream - Based on an Ibanez® TS-9 808 - Based on an Ibanez TS-808 Tube Screamer Spark - Based on a Voodoo Lab Sparkle Drive oddriv - Based on a Guyatone® Overdrive OD-2 dod250 - Based on a DOD® 250 Overdrive/Preamp redlne - DigiTech Redline - Modified Overdrive rodent - Based on a Pro Co RATTM mxdist - Based on an MXR® Distortion + DSDist - Based on a Boss® DS-1TM Distortion 18 Distortion models. Press this knob to turn grunge - DigiTech® Grunge® zone - Based on a Boss MT-2 Metal Zone® death - DigiTech Death MetalTM gonklt - Based on a DOD Gonkulator Ring Mod 8tavia - Based on a Roger Mayer OctaviaTM fuzltr - Based on a Demeter Fuzzulator clasfz - Based on a DOD Classic Fuzz fuzz - Based on an Arbiter® Fuzz FaceTM big pi - Based on an Electro-Harmonix® Big Muff Pi® Disclaimer: AutoYa, DigiTech, DOD, Death Metal, Johnson Amplification, Grunge, Lexicon, Multi Chorus, Whammy, and YaYa are trademarks of Harman International Industries, Inc. Other product names modeled in this product are trademarks of their respective companies that do not endorse and are not associated or affiliated with DigiTech or Harman International Industries, Inc. They are trademarks of other manufacturers and were used merely to identify products whose sounds were reviewed in the creation of this product. 14 Knobs 2-6 have the following functions for the various Distortion models: Dist. Model Scream 808 SPArK oddriv DOD250 redlne rodent mxdist dsdist Grunge zone death gonklt 8tavia fuzltr clasfz fuzz big pi Knob 2 (Gain) Drive Overdrive Gain Drive Gain Gain Distortion Distortion Gain Grunge Gain -Gunk Drive Fuzz Fuzz Fuzz Sustain Knob3 (Param. 1) Tone Tone Tone --Low Filter -Tone Butt Low Low Smear -Tone Tone -Tone Knob 4 (Param. 2) --Clean --High ---Face Mid Mid Suck -Loose/Tight ---Knob5 (Param. 3) ----------High High ------Knob 6 (Distortion Level) Level Level Volume Level Level Level Level Output Level Loud Level Level Heave Volume Volume Volume Volume Volume P7 (X-EditTM only) ----------Mid Freq -------- 15 Amplifier Amp Modeling is a technology which applies the tone of several popular modern and vintage amps. Amp Modeling also includes an acoustic guitar simulation. Note: You can select different Amp models and/or modify Amp settings for each amp channel (Amp A and Amp B). When the Amp row is selected, press the AmpA/BFootswitch to select a channel. The display will show which channel is selected (Amp A or Amp B). [. . . ] Press and hold the Store button while powering up the RP355. When the display prompts you with FACrSt, release the Store button, which is now flashing. Press and hold the flashing Store button for 3 seconds until rStOrD appears in the display and release. The Restore procedure takes several seconds to complete; during the procedure, the display will count up. [. . . ]