User manual DIGITECH RP90

[. . . ] Modeling Guitar Processor Owner's Manual Safety Information WARNING FOR YOUR PROTECTION READ THE FOLLOWING: KEEP THESE INSTRUCTIONS The symbols shown above are internationally accepted symbols that warn of potential hazards with electrical products. The lightning flash with arrowpoint in an equilateral triangle means that there are dangerous voltages present within the unit. The exclamation point in an equilateral triangle indicates that it is necessary for the user to refer to the owner's manual. These symbols warn that there are no user serviceable parts inside the unit. [. . . ] 2. Input Connect your instrument to this high-impedance TS input. Amp / Mixer This button optimizes the RP90's outputs for use when plugged into a guitar amp or a mixer/recording device. When set to Mixer ("In" position), the outputs are optimized for connecting to a mixer, recording device or headphones. When set to Amp ("Out" position), the outputs are optimized for running directly in to the input of a guitar amp. Left (Mono) and Right Outputs Connect the Left (Mono) output to the input of a single amplifier (or mixer input) for mono operation. Connect the Left and Right outputs to the inputs of 2 amplifiers (or 2 mixer channels) for stereo operation. 3. 10 4. Headphones Connect a pair of stereo headphones to this 1/8" jack. For proper frequency response, the Amp/Mixer switch should be set to Mixer ("in" position) when using headphones. Headphones with an impedance of 100 Ohms or less are recommended. Note: The Headphones output can have either a mono or stereo signal, depending on what 1/4" outputs are connected. If neither (or both) 1/4" outputs are connected, the Headphones output will be in stereo. If a cable is connected to the Left (Mono) 1/4" output only, the Headphones output will be in mono. 5. Power Input Connect only the DigiTech® PS200R power supply to this jack. 11 12 Getting Started Making Connections There are several different connection options available with the RP90. Before connecting the RP90, make sure that the power to your amplifier and the RP90 is turned off. To turn the RP90 on or off, connect or disconnect the included PS200R power supply from the PowerInput jack. Mono Operation - Amplifier Connect your guitar to the Input of the RP90. Connect a single mono instrument cable from the Left (Mono) output of the RP90 to the instrument input or effect return on your amplifier. Set the Amp/Mixer switch to Amp. Guitar Amp Input/ Effect Return Left (Mono) Output Input NOTE: When using a guitar amp, it may be best to connect the Output of the RP90 to the effect return of the amplifier. Amp/Mixer switch set to Amp. 13 Stereo Operation For stereo operation connect the guitar to the Input of the RP90. Connect one cable to the RP90's Left (Mono) output, and another cable to the RP90's Right output. Connect one cable to the input of one amplifier, channel of a mixer, or power amp. Connect the second cable to a second amplifier, second channel of a mixer, or power amp. If connecting to a mixing console, set the pan controls of the mixer channels hard left and right in order to retain stereo separation. If connecting to a mixer, set the Amp/Mixer switch to Mixer. If connecting to two amplifiers, set the Amp/Mixer switch to Amp. Stereo Amp Setup Guitar Amp Input/Effect Returns NOTE: When using a guitar amp, it may be best to connect the Output of the RP90 to the effect return of the amplifier. Outputs Amp/Mixer switch set to Amp. Input 14 Stereo Mixer Setup Outputs Mixer 4 2 0 4 2 0 -1 -2 -3 -4 -5 6 82 4 6 82 0 4 82 4 6 82 0 4 82 0 -1 +2 -2 +3 -3 +4 -4 4 6 82 0 4 82 0 -1 +2 -2 +3 -3 +4 -4 -5 4 6 82 0 4 82 0 -1 +2 -2 +3 -3 +4 -4 -5 4 6 82 0 4 82 0 -1 +2 -2 +3 -3 +4 -4 -5 4 6 82 0 4 82 0 -1 +2 -2 +3 -3 +4 -4 -5 4 6 8 0 4 82 0 -1 +2 -2 +3 -3 +4 -4 -5 Instrument Input Aux 1 10 6 Aux 1 10 6 Aux 1 10 6 Aux 1 10 6 Aux 1 10 6 Aux 1 10 6 Aux 1 10 6 Aux 1 10 6 8 Aux 2 10 0 +1 Aux 2 10 0 +1 Aux 2 10 0 +1 Aux 2 10 0 +1 Aux 2 10 0 +1 Aux 2 10 0 +1 Aux 2 10 0 +1 +2 0 -1 -2 +3 -3 Aux 2 10 0 +1 +2 +3 +4 +4 -4 -5 Pan +5 Pan +5 Pan +5 Pan +5 Pan +5 Pan +5 Pan +5 -5 Pan +5 Mute L/R Mute L/R Mute L/R Mute L/R Mute L/R Mute L/R Mute L/R Mute L/R +10 +5 0 -5 -10 +10 +5 0 -5 -10 +10 +5 0 -5 -10 +10 +5 0 -5 -10 +10 +5 0 -5 -10 +10 +5 0 -5 -10 +10 +5 0 -5 -10 +10 +5 0 -5 -10 -20 -30 - -20 -30 - -20 -30 - -20 -30 - -20 -30 - -20 -30 - -20 -30 - -20 -30 - 1 2 3 4 5 6 Amp/Mixer switch set to Mixer 15 Applying Power Before applying power to anything, set your amp(s) to a clean tone and set the tone controls to a flat EQ response (on most amps, this would be 0 or 5 on the tone controls). [. . . ] Change their values with the Value Up/Down buttons. The drum machine has the following parameters Drum Patterns Drum Tempo Drum Level 1-40 1-99 (equivalent of 40 ­ 240BPM) 0-99 Drum machine settings are globally set and not individually stored with each of the RP90's user presets. Factory Reset This function resets the RP90 to its original factory settings. This procedure erases all custom User presets. ATTENTION:Performingthisfunctionwillerasealluser-programmeddata. Allsuch datawillbelostforever!BesureyouwanttoerasethememoryandreturntheRP90 to its factory default state before continuing with this procedure. [. . . ]