User manual DIGITECH VOCALIST LIVE PRO

[. . . ] IMPORTANT SAFETY INSTRUCTIONS WARNING FOR YOUR PROTECTION PLEASE READ THE FOLLOWING: KEEP THESE INSTRUCTIONS HEED ALL WARNINGS FOLLOW ALL INSTRUCTIONS The symbols shown above are internationally accepted symbols that warn of potential hazards with electrical products. The lightning flash with arrowpoint in an equilateral triangle means that there are dangerous voltages present within the unit. The exclamation point in an equilateral triangle indicates that it is necessary for the user to refer to the owner's manual. These symbols warn that there are no user serviceable parts inside the unit. [. . . ] The Lead FX and Reverb/Delay buttons light on the front panel indicating the status of their parameters. Toggles the Harmony Voices, Lead Effects and Reverb and Delay Effects of the current preset Off and On. The Lead FX, Harmony and Reverb/Delay buttons light on the front panel indicating the status of their parameters. The Harmony Voices, Lead Effects and Reverb and Delay Effects are active while the specified Footswitch is pressed and deactivated when released. The Lead FX, Harmony and Reverb/Delay buttons light on the front panel indicating the status of their parameters. Low is the most common setting for Guitar Sensitivity and should provide the guitar input a healthy signal strength indicated by the Guitar Input Signal LED. Some older guitars send a low signal strength. If your guitar doesn't send a strong enough signal to turn the Guitar Signal LED green, try setting the Guitar Sensitivity to High. Footswitch 1, Footswitch 2, Footswitch 3 Gtr Sensitivity High 23 VL. Pro. Owner's. Manual The. MIDI/Expression. Pedal. Setup. Menu The. MIDI/Expression. Pedal. Setup. Menu CC/PC Channel Harmony Instrument CH Harmony 4-Ch Notes V1 Ch Harmony 4-Ch Notes V2 Ch Harmony 4-Ch Notes V3 Ch Harmony 4-Ch Notes V4 Ch Defines the MIDI CC (Continuous Controller) and PC (Program or Preset Change) Channels being used at the MIDI In and USB ports of the Vocalist® Live Pro. Range: Off, All and 1 to 16 Defines which of the MIDI channels the Vocalist Live Pro will read note data and pitch bend data from for musIQTM MIDI, Chordal, and Notes Harmony Modes. Range: All and 1 to 16 Defines which MIDI Channel the Vocalist Live Pro will read note data and pitch bend data from for Harmony Voice 1 when 4-Channel Notes Harmony Mode is selected. Range: 1 to 16 Defines which MIDI Channel the Vocalist Live Pro will read note data and pitch bend data from for Harmony Voice 2 when 4-Channel Notes Harmony Mode is selected. Range: 1 to 16 Defines which MIDI Channel the Vocalist Live Pro will read note data and pitch bend data from for Harmony Voice 3 when 4-Channel Notes Harmony Mode is selected. Range: 1 to 16 Defines which MIDI Channel the Vocalist Live Pro will read Note Data and Pitch Bend Data from for Harmony Voice 4 when 4-Channel Notes Harmony Mode is selected. Range: 1 to 16 Controller 1 Controller 2 Controller 3 Controller 4 Controller 5 Controller 6 Controller 7 Controller 8 Controller 9 Controller 10 Controller 11 Controller 12 Controller 13 Controller 14 Controller 15 Controller 16 Table Continued Next Page CC/ Expr-Pdl/ Controller Map Maps the specified MIDI Controller to the Expression Pedal, a MIDI CC (CC0 to CC127), or turns the Controller Assignment Off by selecting No CC. Once the Controller Mapping is complete, these defined Controllers can be assigned to Expression Links control functions uniquely for individual presets in the Edit Presets menu. Note that the Controller Mapping to the Expression Pedal corresponds to the Expression Pedal Input on the rear panel, as MIDI Expression Pedals provide CC channel messages. If Expression Pedal is selected, then be sure to set the Expression Pedal Type to match your expression pedal in the Global I/O Setup menu. Range: No CC, EXP PDL, CC 0 to CC127 VL. Pro. Owner's. Manual 24 The. MIDI/Expression. Pedal. Setup. Menu MIDI/Expression Pedal Setup Table (Continued) <No Change> MIDI 1128 = VL U1-99, F129 Exits Patch Wizard with no changes applied Sets the MIDI PC definition to associate the User Preset Bank presets to the first 99 programs of the PC message and the first 29 Factory Preset Bank presets to the following 29 programs Sets the MIDI PC definition to associate the Factory Preset Bank presets to the first 99 programs of the PC message and the first 29 User Preset Bank presets to the following 29 programs. Patch Wizard Preset Map MIDI 1128 = VL F1-99, U129 MIDI Program To Edit Selects the MIDI PC preset definition to alter with the Vocalist® Live Pro Preset At n menu function. As you cycle through the MIDI Program definitions, the associated Preset Bank and Number are shown in brackets. Where n refers the MIDI PC program selected with the MIDI Program To Edit, This parameter allows you to redefine the MIDI Program to the desired Vocalist Live Pro preset in any of either the User or Factory Preset Banks. VL-Pro Preset At n Pitch Bend Range Defines the MIDI Pitch Bend Range for the Controllers in Semitones. If +/- 24 Semitones are defined, this gives you a bend range of 48 semitones equal to 4 octaves (2 negative octaves plus 2 positive octaves bend range). Range: +/- 0 to 24 Semitones Disabled Disables MIDI Split Zone functionality. [. . . ] · Ensure the MIDI keyboard is turned on. 57 VL. Pro. Owner's. Manual Troubleshooting · Check that when you play the keys, the MIDI activity is reflected on the MIDI LED on the front panel. · Confirm that the current preset is either using the musIQ Harmony Mode and the Harmony Mode ­ musIQ MIDI button is selected, or that the Harmony Mode - Other (Menu) button is selected and the current preset is using Chordal, Notes or 4-Channel Notes Harmony Mode. · Ensure that in the MIDI/Expression Pedal Setup menu, the Harmony Instrument CH is set All or to the MIDI channel your MIDI keyboard will be sending note and pitch bend data on. · Unless your are intentionally using the MIDI Split Zone functionality, ensure that in the MIDI/ Expression Pedal Setup menu the Split Zone is set to Disabled. [. . . ]