User manual DILLON PRECISION SUPER 1050

[. . . ] Dillon Super 1050 Instruction Manual May 2007 illon recision Products, Inc. Manufacturers of The World's Finest Loading Equipment Table of Contents Super 1050 Package Contents How the Super 1050 Works: Stations 1 - 8 Super 1050 Assembly Powder Measure Adjustments Primer Magazine Electric Casefeeder Review: How the Super 1050 Works: Stations 1 - 8 To Begin Reloading Adjustments Casefeeder Handle Swager Swage Conversion & Adjustment Primer System Change Over Instructions Toolhead Removal Shellplate Removal Casefeed Plunger Conversion Die Adjustments Sizing/Decapping Die - Station 2 Back-up Expander Die & Swager - Station 3 Powder Die - Station 5 Bullet Seating Die - Station 7 Crimp Die - Station 8 RL 1050 vs. Super 1050 Troubleshooting Maintenance Lubrication Points Caliber Conversion Charts Parts List Schematics 4 5 6 8 9 10 10 10 12 12 12 12 12 13 14 14 15 15 15 15 16 17 18 19 19 20 21 - 22 24 - 25 26 27 - 31 2 Warranty Agreement The Dillon Super 1050 reloader has been designed as a commercial machine. Our expectation is that its life expectancy will be in excess of two million rounds of loaded ammunition. All Super 1050 machines are warranted for life from defects in material or workmanship, plus a one-year, 100% warranty against normal wear. [. . . ] 40 - A special screwdriver for the bushing has been included in your accessory bag. You should clean your machine at this time. 42 - After removing the clip and disconnecting the rod, replace the clip in the rod for safe-keeping. Toolhead Removal Disconnect the powder bar return rod (#13960) from the bellcrank (#11234) by releasing the return rod clip (#13929). 42 Remove the Primer Early Warning device. Raise the primer slide lever assembly (#20488) and lock in place - see Fig. Obtain a 15/16" socket or wrench (not supplied) to remove the toolhead bolt (#13342) and washer (#13449). Due to being spring loaded, there will be some resistance. Wiggle the toolhead up and off while holding the handle. After removing the toolhead, carefully lower the handle. When reinstalling the toolhead bolt (#13342) turn it in only finger tight then cycle the handle up and down to make Fig. 41 - It is very important to keep the machine free of grit and debris. Prior to installation, lube the base of the primer punch. Now adjust your new punch (#12849 - large or #13307 small) so that it is flush with the bushing (#13130 - large or #13222 - small) by turning set screw (#13226) up or down. If the primer punch is too low, dirt will Fig. 44 - Your machine will work its best when properly cleaned and lubricated. Rule of thumb: turn the lock ring down until tight then back off one-eighth of a turn. Then tighten the four locator tab screws (#13895). 14 Casefeed Plunger Conversion When changing calibers it may be necessary to replace the casefeed plunger (#13073*). To do this, remove the clear casefeed tube (#20533*) and pull out the colored casefeed adapter (#13654*). The adapter is taped for shipping purposes. Remove the two housing screws (#13815) and the casefeed adapter housing (#11006). Place your hand on the plunger while removing the roller bolt (#13333). This will prevent the casefeed plunger and spring from jumping out of the machine. 45 grease the roller (#13498) and the roller track (Fig. 46) and Loctite the threads on the roller bolt (#13333). Install the casefeed housing and insert the proper size adapter (#13654*). [. . . ] Expander - F 13878 Adapter - Green 13306 Casefeed Plunger - Small 17384 Blue Locator Tab - Short (1) 13569 Blue Locator Tab (5) 14067 Die Lock Ring 13005 Powder Activator - Pistol . 38 Super Comp Conv. - #21069 12441 #3 Shellplate 14060 #3 Locator Pin (6) 12833 9mm cal. Expander - F 13878 Adapter - Green 13306 Casefeed Plunger - Small 17384 Blue Locator Tab - Short (1) 13569 Blue Locator Tab (5) 14067 Die Lock Ring 13005 Powder Activator - Pistol . 38 Special/. 357 Mag. - #20477 12704 #2 Shellplate 14062 #2 Locator Pin (6) 13137 . 38/. 357 cal. [. . . ]