User manual DIRECTV UNIVERSAL 2

[. . . ] ® DIRECTV® Universal Remote Control User's Guide TABLE OF CONTENTS Introduction . . 10 Setup Codes for DIRECTV HD Receivers . . 11 Deactivate the TV Input Select Key . . 11 Programming Other Component Controls . [. . . ] Using the number keys enter the 5-digit code for your brand of component being programmed. If performed correctly the green light under TV will flash twice. Aim the remote at your component and press the power key once. If it does not turn off, repeat steps 3 and 4 trying each code for your brand until you find the correct code. Repeat steps 1 through 6 to program a new component under AV2 (or AV1). For future reference write down the working code for the component(s) programmed under AV1 and AV2 in the blocks below: 5. 6. 7. Move the slide switch to the AV1, AV2 or TV position. Press and hold the MUTE and SELECT keys at the same time until the green light under the selected switch position flashes twice and then release both keys. Enter in 9-9-1 followed by one of the following 4-digits: COMPONENT TYPE Satellite TV VCR/DVD/PVR STEREO 6. COMPONENT ID # 0 1 2 3 4. Point the remote at the TV or component and press CHAN . Repeatedly press the CHAN until the TV or component turns off. Note: Every time CHAN is pressed the remote advances to the next code and power is transmitted to the component 7. When the TV or component turns off, stop pressing the CHAN key. Then, press and release the SELECT key. NOTE: If the light flashes 3 times before the TV or component responds, then you've cycled through all codes and unfortunately the code you need is not available. You must use the remote that came with your TV or component. VERIFYING THE CODES If you have setup the DIRECTV Universal Remote Control using the SEARCHING FOR YOUR CODE PROCEDURE, you can find out the 5-digit code your component responded to with the following instructions: 1. Move the slide switch to appropriate position. Press and hold the MUTE and SELECT keys at the same time until the green light under the selected switch flashes twice and then release both keys. Enter in 9-9-0 (The green light under the selected switch position will flash twice) To view the first digit in the code, Press and release the number 1 key. Wait three seconds, and count the number of times the green light flashes. Write this number down in the leftmost TV, AV1 or AV2 code box found on pages 11 or 12. Note: If this part of the code is "0" the light will not flash 3. 4. 23 5. Repeat step 4 four more times for the remaining digits. Press number 2 for the second digit, 3 for the third digit, 4 for the fourth digit and 5 for the final digit. CHANGING VOLUME LOCK Depending on how you set up your remote, the VOL and MUTE may control the volume only on your TV or other components, regardless of which position the switch is under. This remote can be programmed so that the VOL and MUTE keys work ONLY with the component selected above the slide switch. [. . . ] DIRECTV EXPRESSLY DISCLAIMS ANY REPRESENTATION OR WARRANTY THAT THE DIRECTV UNIVERSAL REMOTE CONTROL WILL BE ERROR FREE. NO ORAL ADVICE OR WRITTEN INFORMATION GIVEN BY DIRECTV, ITS EMPLOYEES, AND LICENSORS OR THE LIKE SHALL CREATE A WARRANTY; NOR SHALL CUSTOMER RELY ON ANY SUCH INFORMATION OR ADVICE. UNDER NO CIRCUMSTANCES, INCLUDING NEGLIGENCE, SHALL DIRECTV OR ANYONE ELSE INVOLVED IN ADMINISTERING, DISTRIBUTING, OR PROVIDING THE DIRECTV UNIVERSAL REMOTE CONTROL BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOSS OF REVENUES OR INABILITY TO USE THE DIRECTV UNIVERSAL REMOTE CONTROL, MISTAKES, OMISSIONS, INTERRUPTIONS, DEFECTS, FAILURE OF PERFORMANCE, EVEN IF DIRECTV HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES. Because some states do not allow the exclusion or limitation of liability for consequential or incidental damages, in such states, DIRECTV's liability is limited to the greatest extent permitted by law. 27 ADDITIONAL INFORMATION This product does not have any user-serviceable parts. [. . . ]