User manual DIRT DEVIL CPB-100

[. . . ] 3) Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes. 4) Use only as described in this manual. Use only manufacturers recommended attachments. [. . . ] 15) Do not pick up flammable or combustible liquids such as gasoline or use it in areas where they may be present. 16) Use extra care when cleaning on stairs. Save These Instructions. INTENDED FOR HOUSEHOLD USE ONLY. 2 S P E C I A L F E AT U R E S Edge Cleaner Active brush edge cleaners are on both sides of the POWERHEAD electric brush. Guide either side of the brush along baseboards or next to furniture to help remove dirt trapped at carpet edges. Warning Lamp Overload Protector The overload protector protects the motor from brush jamming and belt breakage. If the agitator slows down or stops, the overload protector shuts off the brush. To correct problem: To reset: Circuit Breaker Switch Unplug the electrical cord, remove obstruction. Check brush area for excessive lint buildup or jamming. Press the reset button on top of the brush. Plug in the power cord, turn on vacuum and brush. WA N D S & AT TA C H M E N T S Telescoping Wand The wand length is adjustable and requires no assembly. To adjust, simply pull up or push down on the wand adjustment collar and adjust to the desired height. DO NOT attach or remove handle or wands while cleaner is ON. This could cause sparking and damage the electrical contacts. Wand Attachment Handle Release Engaging the pedal on the back of the POWERHEAD marked "handle release" unlocks the pedal from its upright position for vacuuming. For cleaning in those hard-to-reach places such as ceiling or baseboards, the telescopic wand can be disengaged from the neck by depressing the attachment collar as shown and removing the wand. Reinsert by 'clicking' the wand back into place when done. Bottom Plate Screws 3 PILE HEIGHT SETTINGS Pile Height Indicator Suggested pile height settings: XHI HI AUTO MED LO XLO To adjust the carpet height setting of the POWERBRUSH, press the right pedal located on the back of the brush. Each press of this pedal will adjust the height to the next carpet height position. The current height position can be viewed through the height indicator window on the top of the unit. As a general guide: XLO -- low pile carpet (indoor/outdoor type) LO -- short to medium pile MED -- medium to long pile AUTO -- general pile thickness and bare floors HI -- thick pile XHI -- very thick pile Pile Height Pedal ELECTRIC BRUSH CARE Always follow all safety precautions when cleaning and servicing the POWERHEAD. Electrical Shock or Personal Injury Hazard XHI Disconnect electrical supply before servicing or cleaning the unit. Failure to do so HI could result in electrical shock or personal AUTO injury from cleaner suddenly starting. MED LO 3) With the 2 large rear wheels facing you, lift up the backplate and tilt it forward from the back until the front snaps free. Covering the right side of the wood agitator is a black protective belt housing, un-clip and remove. 4) Life the agitator assembly out and remove broken or worn belt. 5) Install the new belt over the motor drive and the other end over of the agitator assembly as shown. Belt Changing XLO Disconnect cleaner from electrical outlet. [. . . ] Simply pull the bulb out (no twisting) and reinsert factory-authorized bulb. Place the top cover back on the unit, turn the machine over and re-insert the two top cover screws. Reinstall the bottom plate. 5 E X P L O S I O N PA R T S & L I S T 6 E X P L O S I O N PA R T S & L I S T DIAGRAM # 1 2 3 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 STOCK # C350-1000 B350-1515 C350-7143 C350-4543B B350-4714 B350-7343 B350-7243 B350-7700 B350-7600 B350-7443B B350-7543B C350-5100 B350-5943 B350-2601 B350-2801 A732-8405 B350-5114 C350-9900 B350-3400 B350-3500 B350-2214 B350-8700 B350-8600 B350-3314 B350-8414 B350-6542B B010-0210 C350-1800R C350-9700 C350-4300 B350-5200 B350-0214 B350-5300 B350-5500 B350-5600 B350-2714 B350-5714 B350-5428 B350-4200 C350-9800 B350-4000 B350-3942 B350-3600 B350-4100 A430-0205 B350-3242 C350-3000 A113-2000 B350-2514 A350-0000 A732-8600 B350-6198 A350-0100 B123-0100 DESCRIPTION Top Housing Assembly Headlight Lens Neck Assembly (Fixed) Neck Assembly (Swivel) Teflon Seal Canister Connection Plug Plug Cover Wand Release Axle Wand Release Spring Wand Release Upper Pedal Wand Release Lower Pedal Hidden Raceway Assembly Pedal Tilt Lock Lever Tilt Lock Pin Screws Hi/Lo #8 Hidden Raceway Bottom Housing Assembly Tilt Lock Link Tilt Lock Torsion Spring Bottom Housing* Felt Seal for Bottom Housing Felt Seal for Belt Housing Belt Housing* Belt Housing* Rear Wheel Assembly 57mm/Overmolded w/Brass Bushing Back Wheel Pin 5mm Dia x 38mm Circuit Breaker 2A with wires Height Adjust Assembly LED Assembly Height Adjust Lever Height Adjust Frame Pedal Compression Spring Height Adjust Washer Height Adjust Compression Spring Height Adjust Disk Height Adjust Catch Height Adjust Wheel Axle Stamping Height Adjust Bar Assembly External Retaining Ring 5/16" Axle Height Wheel w/overmold Height Adjust Bar Bottom Plate Screws Pan Head Agitator End Cap w/Overmold Agitator Assembly B Stack Motor Belt Light Bulb T 3 1/4 12V Screws #4x1 1/4" Reflector Light Socket Snap In Wedge Based Wire Connectors Md. 7 * Belt Housing -Before SN 2D0031444 use B350-3314. [. . . ]