User manual DLS PS6A

[. . . ] The filters must be used, if you connect without them the sound becomes bad and you will destroy the tweeter. INSTALLATION Mount the speakers in the door or in the dashboard of your car. Normally they will fit in the facory pre-made mounting holes. If you want an improved sound reinforce with a baffle of MDF-board or similar. An installation high up on the door side is to be prefered. [. . . ] The woofers magnesium cone body delivers a tight & controlled bass. On the following pages you can see how to connect the filters. The filters must be used, if you connect without them the sound becomes bad and you will destroy the tweeter. The speaker cone is made of magnesium, a material of low weight with excellent acoustic qualitys. We recommend you to NEVER touch the cone body of MS5 or MS6 with your fingers. Remaining deformation of the cone body will occour if you touch it. SPEAKER ENCLOSURES If you want to install the speaker in an enclosure the normal size for a sealed type is: 4" (10 cm) speakers : 2-4 liters 5, 25" (13 cm) speakers : 6-8 liters 6, 5" (16, 5 cm) speakers : 10-12 liters 8" (20 cm) speakers : 15-20 liters 6 x 9" speakers : 15-20 liters 7 x 10" speakers : 20-25 liters These volumes are only a guideline. The volumes can vary between different speakers. Contact your local DLS dealer for more exact information about your specific speaker. SPEAKER FACTS FOR DLS REFERENCE SERIES Model Woofer Tweeter Nom. power 50 W 50 W 50 W 50 W 80 W 80 W 80 W 100 W 80 W 100 W Max power 80 W 80 W 80 W 80 W 120 W 120 W 120 W 150 W 120 W 150 W Sensitivity 90 dB 92 dB 92 dB 94 dB 94 dB 94 dB 93 dB 93 dB 90 dB 92 dB Magnet size 80 mm / 3, 15" 90 mm / 3, 54" 90 mm / 3, 54" 80 mm / 3, 15" 90 mm / 3, 54" 100 mm / 4" 120 mm / 4, 7" 145 mm / 5, 7" 90 mm / 3, 54" 100 mm / 4" Inst. depth 50 mm /1, 97" 45 mm / 1, 77" 53 mm / 2, 09" 60 mm / 2, 36" 60 mm / 2, 36" 76 mm / 3" 90 mm / 3, 54" 80 mm / 3, 15" 58 mm / 2, 28" 67 mm / 2, 64" Mounting hole 98 mm / 3, 85" 117 mm / 4, 6" 146 mm / 5, 75" 102 mm / 4" 120 mm / 4, 72" 140 mm / 5, 5" 150x220 mm / 5, 9x8, 7" 156x225 mm / 6, 15x8, 86" 120 mm / 4, 72" 140 mm / 5, 5" Crossover PS4/4A PS5/5A PS6/6A R4 R5A R6A R964 R1070 MS5 MS6 10 cm / 4" 13 cm / 5, 25" 16, 5 cm / 6, 5" 10 cm / 4" 13 cm / 5, 25" 16, 5 cm / 6, 5" 6 x 9" 7 x 10" 13 cm / 5, 25" 16, 5 cm / 6, 5" 20 mm / 0, 8" 25 mm / 1" 25 mm / 1" 20 mm / 0, 8" 25 mm / 1" 25 mm / 1" 25 mm / 1" 25 mm / 1" 28 mm / 1, 1" 28 mm / 1, 1" Separate boxes Separate boxes Separate boxes Separate box Separate box Separate box Separate box Separate box Separate box Separate box RUNNING-IN PERIOD Allow the speakers to play for at least 15-20 hours. After this time the performance is correct. SPEAKER PHASING To be sure to have the correct speaker polarity (phase) you can check this by using a 1, 5 Volt battery. Connect a cable from the battery plus-pole to the speaker plus, and a cable from the battery minus to the speaker minus. If the speakers are correctly connected the speaker cone should move outwards on both right and left channel. This check must be made on the cables going from the speakers, to the output terminals of your car stereo or amplifier. + CONNECTION OF SPEAKERS Make sure you connect the cables with correct polarity to the speakers. The small terminal is minus. - + FILTER/CROSSOVER INSTALLATIONS Filter installation and connection of R4, R5A & R6A Tweeter TWEETER Filter installation and connection of PS4, PS5 & PS6 WOOFER TWEETER Hi Mid Lo Tw select Silver Silver/red Black Black/ blue Tweeter + + 2-way crossover WOOFER - Silver/red Black Black/blue INPUT + - Silver + - + - + - + Bass/mid + + + INPUT Tweeter level select: Select tweeter level by moving the jumper inside the filter box between high, mid or low. Make your own tests for best result. Head unit/amp. - Woofer + + - Head unit / amp. Filter installation and connection of PS4A, PS5A & PS6A TWEETER - Silver - + - Select tweeter level by moving the jumper inside the filter box between high or low. Make your own tests for best result. IN R4 tweeter level select: Hi Low Silver/red + Tweeter Head unit / amp + Black Black/blue + WOOFER - + Woofer Hi Mid Low R5A, R6A tweeter level select: Select tweeter level by moving the jumper inside the filter box between high, mid or low. Make your own tests for best result. IN + - + Tw level Tweeter level select: Select tweeter level by moving the jumper inside the filter box between high, mid or low. Make your own tests for best result. Hi Mid Lo Tw level FILTER/CROSSOVER INSTALLATIONS Filter installation and connection of MS5 & MS6 Tweeter TWEETER 2-way crossover Silver Silver/red Black Black/blue + THE JUMPERS INSIDE THE FILTER: JUMPER J1 Jumper J1 is used for lowering the x-over frequency to the tweeter. J1 position Low: When the tweeter is mounted apart from the bass element (for example on the dashboard), use this position . J1 position Hi: When both tweeter and bass elements are mounted close together (for example in the door side), use this position . WOOFER + - + - + INPUT - Woofer + + Head unit / amp. Hi Mid Low J2 - TWEETER LEVEL: JUMPER J2 Select tweeter level by moving the small jumper J2 inside the filter box. [. . . ] Attach the tweeter element to the angled cup (2) as shown on picture 3. Now the tweeter can be mounted in two different angles. Attach to the surface with the two screws or double adhesive tape. RECESSED MOUNTING: You need a hole with a diameter of 46 mm / 1, 81" in the door side (for UP1C 48 mm / 1, 89"). Put the two metal wings through the two tracks in the center of the cup, just as the picture shows, and attach them with the M4 screw and nut through the center hole. [. . . ]