User manual DLS UR2,5

[. . . ] Normally they will fit in the facory pre-made mounting holes. If you want an improved sound reinforce with a baffle of MDF-board or similar. An installation high up on the door side is to be prefered. An alternative installation is in so called kick panels down on each side of the floor with the speakers facing up- and inwards towards the listener. [. . . ] Contact your local DLS dealer for more exact information about your specific speaker. SPEAKER FACTS FOR DLS ULTIMATE SERIES Model Woofer Mid Tweeter Nom. power 120 W 150 W 120 W 150 W 80 W 100 W 80 W 100 W 80 W 100 W Max power 180 W 180 W 180 W 180 W 120 W 160 W 120 W 160 W 120 W 160 W Sensitivity 89 dB 88 dB 89 dB 88 dB 91 dB 91 dB 91 dB 91 dB 91 dB 91 dB Magnet size 62 mm / 2, 44" 62 mm / 2, 44" 62 mm / 2, 44" 62 mm / 2, 44" 85 mm / 3, 35" 85 mm / 3, 35" 85 mm / 3, 35" 85 mm / 3, 35" 85 mm / 3, 35" 85 mm / 3, 35" Inst. depth 58 mm / 2, 28" 63 mm / 2, 48" 58 mm / 2, 28" 63 mm / 2, 48" 62 mm / 2, 44" 65 mm / 2, 56" 62 mm / 2, 44" 65 mm / 2, 56" 62 mm / 2, 44" 65 mm / 2, 56" Mounting hole 120 mm / 472" 140 mm / 5, 5" 120 mm / 4, 72" 140 mm / 5, 51" 120 mm / 4, 72" 140 mm / 5, 51" 120 mm / 4, 72" 140 mm / 5, 51" 120 mm / 4, 72" 140 mm / 5, 51" Crossover UP5 UP6 UP35 UP36 UR5 UR6 UR5S UR6S 13 cm / 5, 25" 16, 5 cm / 6, 5" 13 cm / 5, 25" 16, 5 cm / 6, 5" 13 cm / 5, 25" 16, 5 cm / 6, 5" 13 cm / 5, 25" 16, 5 cm / 6, 5" 2, 5" 2, 5" 2, 5" 2, 5" 28 mm / 1, 1" 28 mm / 1, 1" 28 mm / 1, 1" 28 mm / 1, 1" 28 mm / 1, 1" 28 mm / 1, 1" 28 mm / 1, 1" 28 mm / 1, 1" 28 mm / 1, 1" 28 mm / 1, 1" Separate box Separate box Separate box Separate box Separate box Separate box Separate box Separate box Separate box Separate box UR35S 13 cm / 5, 25" UR36S 16, 5 cm / 6, 5" RUNNING-IN PERIOD Allow the speakers to play for at least 15-20 hours. After this time the performance is correct. SPEAKER PHASING To be sure to have the correct speaker polarity (phase) you can check this by using a 1, 5 Volt battery. Connect a cable from the battery plus-pole to the speaker plus, and a cable from the battery minus to the speaker minus. If the speakers are correctly connected the speaker cone should move outwards on both right and left channel. This check must be made on the cables going from the speakers, to the output terminals of your car stereo or amplifier. CONNECTION OF SPEAKERS Make sure you connect the cables with correct polarity to the speakers. The small terminal is minus. + - + - FILTER/CROSSOVER INSTALLATIONS Filter installation and connection of UP5 & UP6 Tweeter J2 Input Tweeter Midr. Woofer Filter installation and connection of UP35 & UP36 3-way systems Bass + + + + Mid Tweeter Speaker impedance 4 TWEETER + HI LO + 2-way crossover Mid level WOOFER + Coil J3 Tweeter level - - + INPUT BASS Head unit / amp. The drawing shows the connection of a 3-way system to one channel. The other channel is connected in the same way. The tweeter level is adjustable in three steps, the MID level in two steps: TWEETER LEVEL: JUMPER J2 Select tweeter level by moving the small jumper J2 inside the filter box. High level Mid level Low level Tweeter level (J3): High = jumper in HI-position Mid = jumper in MID-position Low = jumper in LO-position Midrange level J2): High = jumper in HI-position Low = jumper in LO-position Jumper J1 is used when you want to run the system without midbass driver. In this case some components inside the filter must be disconnected. Midbass connected: jumper mounted in IN-position. Midbass disconnected: jumper mounted in OUT-position. J2 Tw level Hi Mid Low NOTE! If the system is used together with a subwoofer, test to phase reverse the subwoofer to see what sounds best. IN OUT + HI MID LO Bass/mid - J1 + _ _ _ _ FILTER/CROSSOVER INSTALLATIONS Filter installation and connection of UR5, UR6, UR5S & UR6S Tweeter TWEETER + + - 2-way crossover WOOFER + INPUT - + - Bass/mid + + Head unit / amp. Hi Mid Low J2 Tw level Filter installation and connection of UR35S & UR36S 3-way systems The drawing shows the connection of a 3-way system to one channel. The other channel is connected in the same way. The tweeter and mid levels are adjustable in two steps as described below: Tweeter level (J3): High = jumper mounted between pin 1-2. Midrange level (J2): High = jumper mounted between pin 1-2. Jumper J1 is used when you want to run the system without midbass driver. In this case some components inside the filter must be disconnected. [. . . ] The cup is attached to the door side when the metal wings is pressed to the back side of the door. Put the tweeter element into the cup with the cable going out through the bottom hole. Then attach the element into the cup and turn it clockwise to attach to the cup. When removing the element from the cup, turn it ccw and lift it out F E RECESSED MOUNTING: A You need a hole with a diameter of 45 mm / 1, 77" in the door side. [. . . ]