User manual DOD D3

[. . . ] DOD warrants this product, when used solely within the U. S. , to be free from defects in material and workmanship under normal use and service. DOD Electronics liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect, provided the product is returned through the original dealer, where all parts and labor will be covered up to a period of one year. The company shall not be responsible for any consequential damage as a result of the product's use in any circuit or assembly. Proof of date of purchase is considered to be the burden of the consumer. Maximum Output Level: 12 dBu Power Requirements: 3 VA Dimensions: 1. 75" X 4. 75" X 19" 5. [. . . ] Adjust the Input Knob until the Clip LED briefly lights when signal peaks are reached. The signal LEDs indicate signal is present at the input. Adjust the Output and Mix Knobs to desired settings. After adjusting the Input, Output, and Mix knobs, determine which effect you want to use. Use the Effect dial to select the effect, and dial up the effect that is most fitting to your needs. Selecting BYPASS (optional DOD FS300 footswitch) will mute the effect signal. After selecting an Effect , you can adjust the available parameters using the Parameter knobs. *Rotary speaker Controls speed and Depth 0. 7 to 10 Hz *In addition to Bypass the optional FS300 footswitch also provides control of all the effects that have a speed parameter. It will allow you to switch between the default lowest setting, and the highest knob setting. This function increases real time playability dramatically. Switching between settings in the Rotary speaker effect causes the speeds and doppler shift to ramp between the two settings. This effect must be heard to be appreciated. O WNER'S M ANUAL DOD Electronics Corporation 8760 South Sandy Parkway Sandy, Utah 84070 International Distribution 3 Overlook Drive Unit 4 Amherst, New Hampshire 03031 U. S. A. FAX (603) 672-4246 DOD is a Registered Trademark of DOD Electronics © 1997 DOD Electronics Corporation Printed In U. S. A. DOD 18-2231-B Dimension3 D O D E L E C T R O N I C S C O R P O R AT I O N WARNING CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING: WATER AND MOISTURE: Appliance should not be used near water (e. g. near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. POWER SOURCES: The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polarization means of an appliance is not defeated. POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. SERVICING: To reduce the risk of fire or electric shock, the user should not attempt to service the appliance beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel. FOR UNITS EQUIPPED WITH EXTERNALLY ACCESSIBLE FUSE RECEPTACLE: Replace fuse with same type and rating only. DECLARATION OF CONFORMITY Manufacturer's Name: Manufacturer's Address: DOD Electronics Corporation 8760 S. Sandy Parkway Sandy, Utah 84070, USA A T T E N T I O N : RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR W A R N I N G : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE These symbols are internationally accepted symbols that warn of potential hazards with electrical products. [. . . ] DOD Electronics Corporation President of DOD 8760 S. Sandy Parkway Sandy, Utah 84070, USA Effective: 11/24/97 European Contact: Your Local DOD Sales and Service Office or International Sales Office 3 Overlook Drive #4 Amherst, New Hampshire 03031, USA Tel (603) 672-4244 Fax (603) 672-4246 As colours of the cores in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: · The core which is coloured green and yellow must be connected to the terminal in the plug marked with the letter E, or with the earth symbol, or coloured green, or green and yellow. · The core which is coloured blue must be connected to the terminal marked N or coloured black. · The core which is coloured brown must be connected to the terminal marked L or coloured red. [. . . ]