User manual DOD GS-300

[. . . ] OK Button 8 Holder Installation Installation Combine the suction cup holder with the host device Memory Card Installation (Optional Purchase) Install the Micro SD card into the drive recorder in the specific direction. 9 Installation on Your Vehicles Step 1 Install the suction cup holder by having it sucked onto the windshield with the lens facing forward. Step 2 Plug the vehicle power cable in the cig lighter, and plug the other end to the DC port of the drive recorder. 10 Step 3 After installation, you may arrange the surplus power cable and hide it inside Column A. Step 4 Switch ON the power, a red light blinking means it is under recording mode; press the infrared-red laser ray button and adjust the lens direction according to the position of the red dot to complete the installation. 11 Transmit the video to the vehicle monitor Video can be transmitted through AV IN interface if there are video equipments (vehicle monitor, GPS, and Satellite TV, etc. ). The following is an example on transmitting the video to the monitor by using GPS with build-in AV IN function. Please skip the steps if you do not have these equipments. Step 5 Insert the AV terminal to the video equipment, plug the other end to PC/AV port of the drive recorder, adjust the video equipment to AV channel, and insert the vehicle power cable to complete the installation. 12 Transmit the video to LCD TV You can also transmit the video from the drive recorder to your LCD TV at home to playback the data or adjust the setting. [. . . ] Remote Controller MENU ButtonSystem SetupMenuTime zone-12/-11/-10/-9/-8/-7/-6/ -5/-4/-3/-2/-1/0/+1/+2/+3 /+4/+5/+6/+7/+8*/+9/+10/+11 /+12 *Setting Value 29 G Sensor sens. X. Y. Z(GS600) When there is a collision, with the help of the changes in XYZ curves, G Sensor or Gravity Sensor can determine the direction of the collision and simultaneously set the recorded data to protection mode, and the data will not be overwritten by circulated recording. Adjust the sensitivity parameter of XYZ axles. [OFF] sensitivity means G Sensor function is OFF, so the drive recorder will not automatically set the data to protection mode, and manual setting will be needed. XLeft and right changes during acceleration. YBack and forth changes during acceleration. ZUp and down changes during acceleration. Remote Controller MENU ButtonSystem SetupMenu G Sensor sens. X. Y. ZOff/1/2/3/4/5 */6/7/8/9/10 *Setting Value 30 TV out This setting can be adjusted when you use AV cable or HDMI cable to transmit the video to the monitor. Select local video specifications NTSC or PAL to solve the problem of flicking pictures owing to inappropriate video format. Remote Controller MENU Button System Setup Menu TV out NTSC*/PAL *Setting Value 31 Stamp Through this function, you can select whether to show time and date during recording. Remote Controller MENU Button System Setup Menu Stamp On*/Off *Setting Value 32 Date & Time Adjust the current date and time. (Drive recorder with GPS feature will automatically sync the standard date and time after positioning, no setting is required). Remote Controller MENU ButtonSystem Setup MenuDate & TimePress "OK" key on Remote Controller to enter setting Press the remote controller, select Year, Month, Day, Time, Minute Press the remote controllerto adjust valuesPress OK Button on the remote controller to save the setting. 33 Format Storage card This function will delete all data in the memory card including protected data. When the memory card is used for a long time, too much data will reduce the access efficiency. This function will optimize the access speed of the memory card. Remote Controller MENU Button System Setup Menu Format Storage cardNo*/ Yes Press OK Button on the remote controller to process *Setting Value 34 Reset This function will reset all settings on the drive recorder to default factory settings. Remote Controller MENU Button System Setup Menu Reset No*/ Yes Press OK Button on the remote controller to process *Setting Value 35 Version View the firmware version of the drive recorder. Remote Controller MENU ButtonSystem SetupMenu Version* *The version number during factory shipment will be considered as the original version. 36 Language Use this setting to adjust the menu to your preferred language. Remote Controller MENU ButtonLanguage MenuEnglish */////P Press OK Button on the remote controller to process *Setting Value 37 Playback Before video playback, please transmit the picture to your monitor (Page12, 13), and use the remote controller to operate (Page 08). [. . . ] Improper rubbing will cause tear or scar on the lens. Please use lens wiper or clothe with minimum clean liquid specified for lens and wipe in concentric circles. 46 Related Parameters Light indication guide Blue light Red light Description Function Memory card is full Memory card not inserted USB mode Formatting ------- --- blink simultaneously blinking alternately Constant blue light GPS positioning completed Red light blinking Recording Constant red light Recording stopped 47 Video Recording Time (For Reference) 1G 17 mins 27 mins 34 mins 35 mins 105 mins 2G 34 mins 54 mins 68 mins 70 mins 210 mins Memory card(GB) 4G 8G 68 136 mins mins 108 216 mins mins 136 272 mins mins 140 280 mins mins 420 840 mins mins 1920x1080(30FPS) 1440x1080(30FPS) 1280x720(30FPS) 848x480(60FPS) 640x480(30FPS) Recording time will be different based on different host devices, memory card brands and other settings. 48 Product Specifications Sensor Lens Focus GPS Video output Recording format Recording resolution Video Codec Recording media Laser LED Light File protection USB Battery Remote control Imposition of date / time on video Size Weight Nutrition Working humidity Temperature GS300 GS600 5 Mega pixels CMOS 120 degree 10cm ­ infinity NO Internal antenna Mini HDMI: Support 1080i/720p output mode Composite: NTSC/PAL MOV 1920x1080(30fps) 1280x720(30fps) 848x480(60fps) H. 264 Micro Card(Up to 64GB SDHC Card) 1 PCS YES Micro USB Internal(DC 3. 7V 190mAh) YES YES 113mm X 24. 1mm X 30mm 122g DC 12-24V 10%~80% -10~70 Actual specifications depend on factory announcement. No further notice will be provided in case of any change. 49 ISO9001:2000 FCC CE SGS 1. (4M)*1 2. 8. DC 9. USB /AV OUT 51 1. Micro-SD 2. /USB 3. [. . . ]